-
LED suppression disabled after reboot
Hi I have two WAC6503D-S connected and managed by a ZyWall VPN 100. After the system is up (the ZyWall and the both AP's), I set the "LED suppression on" on Monitor\Wireless\AP Information\ @ each AP. It works well, the LED's are off. When I reboot the AP's, the LED's are flashing during startup, what is fine. But after…
-
nxc-2500 change psk key with cli
Hello! over telnet after login ... configure terminal wlan-security-profile guest_sec wpa-psk blablablablawrite exit become the wpa-psk changed and on the gui correct showed but wlan login dont work.I think i need some as "apply" on the cli ?on the gui, after wlan-psk rewrite and "OK" then works ...Thanks in advance...
-
How to switch WAC AP to Nebula from on-premises controller
This article is shown you how to switch AP to Nebula from on-premises controller. Please follow these steps to migrate your AP to the cloud and enjoy managing your network anywhere and anytime. Apply to WAC6103D-I, WAC6502D-E, WAC6502D-S, WAC6503D-S, WAC6552D-S, WAC6553D-E Step1: Go to Nebula Control Center to register…
-
WAC5302 constantly rebooting
Hello We have the following setup in a customer installation Zywall USG-40 as AP controller for 6 WAC5302 Accesspoints. A additional 4 AP license is installed on the USG. Firmware for the USG is V4.33(AALA.0) Firmware on the accesspoints is V5.00(ABFH.5) The accesspoints are rebooting every 2..3 minutes. In the logs, I get…
-
Reboot remotely a LTE3301-Q222
Hi,I'd like to be able to reboot remotely a LTE3301-Q222 via Wi-Fi but I cannot figure out how to do that. I tried to connect with telnet but I don't know the password. I tried the default password and the admin password but none of them work. How could I do that?
-
Printer can't join the network?
Hi all I have several networked build with WAC6103. Some location setup with an USG60/110/310 and some with NXC2500. There is the same issue all over. If I take a printer (HP PageWide, Epson, Canon etc, etc) and trys to connect it, it fails.The HP PageWide gives most details - That Its see the same network name on more…
-
NWA1123-AC: What's username/password?
I have a NWA1123-AC with firmware version V2.12(AAOX.0). I backed up my config, but after reloading it my personal username and password don't work anymore. Neither do the default credentials, as in admin/1234. What's going on? They only way out it seems is by resetting the device, but that's defeating the purpose of being…
-
NWA1123-ACv2 Roaming configuration
Hi, I have two NWA1123-ACv2 - how can I configure roaming so I do not need to disable / enable wifi to get to the strongest AP connected? Thanks! Best regards #Biz_Apr_2019
-
QOS on VMG1312-B10D for SIP trunks
Hello trying to set up QOS for SIP trunks on this router but when trying to set up the classifier if I select the VDSL interface it locks up the classifier section so the only way I can then access it again is to default the router. Could be something i'm doing as i'm not 100% sure on how to set up the QOS correctly on…
-
samsung mobile phone (j7, S7) and iphone do not receive or send multimedia files by WAC6503D-S, what
I bought about 16 WAC6503D-S access points, I configured a 2.4Gh network and a 5Gh network.Testing with huawei mobile I have no problem, when I connect a samsung device (J7 Prime and S7 Edge), I do not download any multimendia file, the same thing happens with Iphones.I thought it was going to be some problem with the WIFI…
-
Cannot connect to NXC2500 via 192.168.1.1
I cannot connect the NXC2500 to my computer via 192.168.1.1 even after I reset the unit. I tried from port 1 to port 6. Error message : This site can’t be reached
-
WPA3
The Wi-Fi Alliance announced WPA3 a few months ago, a Wi-Fi security standard that will replace WPA2. When it will be able on current Zyxel devices? Is it on the roadmap?
-
Single-channel wifi design instead of standard multi-channel
Hi, I'm interesting in another wifi design than classic. Standard design with APs managed by WLC use different channels (e.g. for 2,4GHz ch.no. 1, 6 and 11) which alternates from one AP to the second. This design is very usefull, if wifi-clients don't move too much or too quickly. But if wifi client moves, especially if it…
-
IGMP / Wireless /
Dear Zyxel. I am not sure it's the correct question in the switch section but let's see.. Maybe it's a dum question but that is caused by lack of experience with this scenario. Normally with IPTV you have this topology What now when i have the possibility to connect my TV(setup box) wirelessly to the topology like this:…
-
Configuration of Three NWA1123-AC-PRO with cable lan
Hello to all, as object, I've Three ap NWA1123-AC-PRO (not nebula mode) all connected in same lan with wire cable. I would like to cover a single floor of my house. I would like to use a single SSID and same password and allow all devices to be covered while I move.How should I configure APs so that I don't conflict? Thank…
-
NXC2500 does not find additional NWA3160
Hi, we bought 2 additional nwa3160 to get them running on our nxc2500. I already got 8 APs up and running but the last two wont be found. Switched them to Managed AP and entered the IP of the NXC2500 . Firmware version is V3.72 . Can anyone please help me out? Best regards... Mirko
-
Zyxel WAC-6503d-s
for my 2 access points I allow the following services (AP_To_Device):- CAPWAP-CONTROL- CAPWAP-DATA- DHCPv4- PING But somehow I still see some traffic DROPPED from the AP's to the Device.Though it seems that the AP's are working fine, I still wonder what could be this traffic and what kind of request this is from the AP to…
-
Mixing different types of NWA
Is it possible to have a NWA1123-ACV2 as Root AP and NWA1100-NH or NWA110-N in repeater mode in the same system?
-
Zyxel AP Configurator - File Transferring Failed
Dear community. I am owning WAC6103D-I and today I am trying out Zxyel AP Configurator and set up the SNMP Get Community accordingly. My access point could be found using discovery. However, when clicking on "Next" button I credential prompt and entered my admin credentials. But after that I am getting an error message…
-
Help configuration Three nwa1123 ac-pro
Hello I have n.3 Ap in standalone mode, all connected to lan by cable. I'd like to create a mesh configuration with a single ssid ... to understand.how should I proceed? #Biz_WLAN_Mar_2019