NWA1123-AC-HD
![Damien_SBM](https://us.v-cdn.net/6029482/uploads/defaultavatar/nN4PAQRO7TCNP.jpg)
![First Anniversary](https://us.v-cdn.net/6029482/uploads/badges/SJKCAIG91R5S.png)
![Friend Collector](https://us.v-cdn.net/6029482/uploads/badges/HNJASEUSC535.png)
![First Comment](https://us.v-cdn.net/6029482/uploads/badges/MBNFIRD87YVH.png)
Hi everybody,
I would know if it's possible to have Two SSID with different range address ip ?
Or it's exclusive to Nebula ?
Thanks
Accepted Solution
-
Hi @Damien
Yes, it is possible to have two SSIDs with different IP address ranges. As PeterUK mentioned, you can achieve this by setting up VLANs on your Zyxel Access Point (AP) and configuring your USG FLEX firewall to handle the different IP address ranges for each VLAN.
Here's a brief overview of the steps:
- Configure VLANs on the USG FLEX:
- Log in to your USG FLEX web interface.
- Navigate to Configuration > Network > Interface > VLAN.
- Create VLANs for each SSID with the desired IP address range.
- Set up SSIDs on the Access Point:
- Log in to your Zyxel Access Point's web interface.
- Go to Configuration > Wireless > SSID.
- Create or edit the SSIDs and assign them to the corresponding VLANs.
- Assign VLANs to SSIDs:
- In the same SSID configuration section, ensure each SSID is tagged with the correct VLAN ID.
- VLAN Traffic Through Switches:
- Ensure VLAN traffic is allowed if there is any switch between your AP and firewall.
For more details about creating SSIDs in standalone mode, you may refer to this article:
Kay
Don't miss this great chance to upgrade your Nebula org. for free! https://bit.ly/4g2pS9L
0 - Configure VLANs on the USG FLEX:
All Replies
-
You need a USG doing VLANs to do this
0 -
an USG FLEX 500 can make it ?
0 -
Yes then with the AP and PoE+ to USG and AP config the given VLAN IP subnet on that base port with a zone with SSID AP setting to the given VLAN ID
0 -
Hi @Damien
Yes, it is possible to have two SSIDs with different IP address ranges. As PeterUK mentioned, you can achieve this by setting up VLANs on your Zyxel Access Point (AP) and configuring your USG FLEX firewall to handle the different IP address ranges for each VLAN.
Here's a brief overview of the steps:
- Configure VLANs on the USG FLEX:
- Log in to your USG FLEX web interface.
- Navigate to Configuration > Network > Interface > VLAN.
- Create VLANs for each SSID with the desired IP address range.
- Set up SSIDs on the Access Point:
- Log in to your Zyxel Access Point's web interface.
- Go to Configuration > Wireless > SSID.
- Create or edit the SSIDs and assign them to the corresponding VLANs.
- Assign VLANs to SSIDs:
- In the same SSID configuration section, ensure each SSID is tagged with the correct VLAN ID.
- VLAN Traffic Through Switches:
- Ensure VLAN traffic is allowed if there is any switch between your AP and firewall.
For more details about creating SSIDs in standalone mode, you may refer to this article:
Kay
Don't miss this great chance to upgrade your Nebula org. for free! https://bit.ly/4g2pS9L
0 - Configure VLANs on the USG FLEX:
-
Thanks a lot !
0
Categories
- All Categories
- 414 Beta Program
- 2.2K Nebula
- 130 Nebula Ideas
- 88 Nebula Status and Incidents
- 5.4K Security
- 166 USG FLEX H Series
- 255 Security Ideas
- 1.4K Switch
- 71 Switch Ideas
- 999 Wireless
- 36 Wireless Ideas
- 6.2K Consumer Product
- 233 Service & License
- 370 News and Release
- 77 Security Advisories
- 24 Education Center
- 5 [Campaign] Zyxel Network Detective
- 2.9K FAQ
- 34 Documents
- 34 Nebula Monthly Express
- 80 About Community
- 69 Security Highlight