[NEBULA] access to Switch nsw100-28

Jclarumbe
Jclarumbe Posts: 3  Freshman Member
First Comment
edited April 2021 in Nebula

I was been configuring the switch nsw100-28 thought webserver in lan with the typical user and password admin/1234. Afterward I've registered the switch NSW100-28 in Nebula CC and now I cant sign up by LAN to the webserver of the switch.

I've tried to sign up with admin / 1234 but I'm not allowed. I used the username and password of Nebula CC as well, but I didnt pass.

In Nebula CC I cant configure the user and password so I don't know what to do.

I didn't configure the vlans so It's necessary to access this way

I don't know how to reset the swich so I can't start as factory default.

Could someone help me?

Best Answers

  • RUnglaube
    RUnglaube Posts: 135  Ally Member
    5 Answers First Comment Friend Collector Third Anniversary
    edited June 2019 Answer ✓

    Once added to NCC, it will set a new password that can be seen/changed on NCC. Go to Site-wide > Configure > General setting and look for local credentials there.

    "You will never walk along"
  • Zyxel_Jason
    Zyxel_Jason Posts: 411  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Engineer Level 1 - Nebula Zyxel Certified Sales Associate
    Answer ✓

    Hi @Jclarumbe,

    Welcome to Zyxel Community!

    When your Switch is registered and gets online on Nebula CC, Nebula CC will push new configuration include new password from Nebula CC.

    You may go to SITE-WIDE > Configure > General setting to check or change new password of the Switch.

    Hope it helps.

    Jason

    See how you've made an impact in Zyxel Community this year!
    https://bit.ly/Your2024Moments_Community
  • Zyxel_Jason
    Zyxel_Jason Posts: 411  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Engineer Level 1 - Nebula Zyxel Certified Sales Associate
    Answer ✓

    Hi @Jclarumbe ,

    You may configure VLAN for every port on NCC by going to "SWITCH > Configure > Switch ports".

    In the port configuration page, you may configure the VLAN Type(Trunk/Access) and the PVID. In Trunk type, you may also configure Allowed VLANs.

    BTW, you may still using WebGUI of the Switch to configure VLAN, but please note that every time you configure VLAN related on NCC, the configuration on device will be overwritten by NCC.

    Hope it helps.

    Jason

    See how you've made an impact in Zyxel Community this year!
    https://bit.ly/Your2024Moments_Community

All Replies

  • RUnglaube
    RUnglaube Posts: 135  Ally Member
    5 Answers First Comment Friend Collector Third Anniversary
    edited June 2019 Answer ✓

    Once added to NCC, it will set a new password that can be seen/changed on NCC. Go to Site-wide > Configure > General setting and look for local credentials there.

    "You will never walk along"
  • Zyxel_Jason
    Zyxel_Jason Posts: 411  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Engineer Level 1 - Nebula Zyxel Certified Sales Associate
    Answer ✓

    Hi @Jclarumbe,

    Welcome to Zyxel Community!

    When your Switch is registered and gets online on Nebula CC, Nebula CC will push new configuration include new password from Nebula CC.

    You may go to SITE-WIDE > Configure > General setting to check or change new password of the Switch.

    Hope it helps.

    Jason

    See how you've made an impact in Zyxel Community this year!
    https://bit.ly/Your2024Moments_Community
  • Jclarumbe
    Jclarumbe Posts: 3  Freshman Member
    First Comment

    All is running perfect. Only one more question..

    Do you know if I can configure the vlans from the NCC or only in webserver?

  • Zyxel_Jason
    Zyxel_Jason Posts: 411  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Engineer Level 1 - Nebula Zyxel Certified Sales Associate
    Answer ✓

    Hi @Jclarumbe ,

    You may configure VLAN for every port on NCC by going to "SWITCH > Configure > Switch ports".

    In the port configuration page, you may configure the VLAN Type(Trunk/Access) and the PVID. In Trunk type, you may also configure Allowed VLANs.

    BTW, you may still using WebGUI of the Switch to configure VLAN, but please note that every time you configure VLAN related on NCC, the configuration on device will be overwritten by NCC.

    Hope it helps.

    Jason

    See how you've made an impact in Zyxel Community this year!
    https://bit.ly/Your2024Moments_Community
  • Jclarumbe
    Jclarumbe Posts: 3  Freshman Member
    First Comment

    Really useful answers. Thank you very much.

Nebula Tips & Tricks