[Release Note] Nebula Control Center - 19.20 software Release!
                
                    Zyxel_CSO                
                
                    Posts: 497 
  Zyxel Employee
         
            
         
         
            
         
         
            
         
         
            
                         
            
                        
            
  Zyxel Employee
         
         
            
         
         
            
         
         
            
         Zyxel Nebula Control Center Release Note
Common NCC (Organization,Site-wide,etc.):
- Rename Clone to Replicate and added support for Site-wide configurations by each product line such as AP, SW, FW and Site settings in Org-wide management use. (Nebula Pro Pack license is required)  

 - Strengthened backup & restore functionality such as scheduling backup, device capacity and supported product types for Org-wide and MSP cross-org management use. These enhancements allow for an expedited and successful recovery when it counts. (Nebula Pro Pack or MSP Pack license is required) 


 - Rename MSP Cross-org synchronization to Config management for consistency. (Nebula MSP Pack license is required)
 - Enhanced MSP portal delivers the device insight that improves overall operational efficiency. (Nebula MSP Pack license is required) 

 - Remote SSH/Configurator is now a complimentary Nebula Base Pack feature. 

 - Added Reprovsion livetool to immediately aligning the device with the latest cloud settings. 

 - Enhanced performance and a refined UI make firmware management clearer and easier to use.
 
Wireless LAN (WLAN):
- The following new AP models are now supported in this release: IAP500BE, NWA30BE and NWA55BE. IAP500BE is a brand-new industrial Wi-Fi 7 NebulaFlex Pro Access Point that comes with 3 management modes: standalone, controller managed and Nebula cloud managed modes. It comes with 1 year Nebula Pro Pack license bundled. NWA30BE and NWA55BE are Small Business-class Wi-Fi 7 NebulaFlex Access Points, supporting both standalone mode and nebula cloud-managed mode. NWA210AXv2 is a Wi-Fi 6 NebulaFlex Access Point, supporting both standalone mode and nebula cloud-managed mode.
 - The enhanced SSID scheduling feature enables users to set multiple on/off periods for each day, making it ideal for scenarios like school environments. Users can also easily duplicate a single day’s schedule to other weekdays. 

 
Switching:
- VLAN ingress checking is force-enabled to enhance security by blocking unauthorized packets. (Exclude NSW100 and NSW200 series)
 
Security Firewall:
- Added IKEv2/SSL VPN remote access feature for USG FLEX H series. 

 - Improved business resilience with added secondary peer gateway support in Manual-link VPN for USG FLEX H series. 

 - Policy Route's next hop now supports to use IPSec VPN tunnel for USG FLEX H series. 

 - Enhanced management clarity by allowing users to assign the custom name to every newly added Phase 2 IPSec rule for USG FLEX H series.
 - Added VTI description for management clarity for USG FLEX H series.
 
Security Router:
- N/A
 
Mobile Router:
- Support the new MR model. The Nebula FWA70 is added to Nebula in this release.
 
Accessory enhancements:
- N/A
 
Zyxel Nebula Support
0    
            Categories
- All Categories
 - 439 Beta Program
 - 2.8K Nebula
 - 200 Nebula Ideas
 - 126 Nebula Status and Incidents
 - 6.3K Security
 - 499 USG FLEX H Series
 - 323 Security Ideas
 - 1.6K Switch
 - 84 Switch Ideas
 - 1.3K Wireless
 - 49 Wireless Ideas
 - 6.8K Consumer Product
 - 287 Service & License
 - 457 News and Release
 - 89 Security Advisories
 - 31 Education Center
 - 10 [Campaign] Zyxel Network Detective
 - 4.3K FAQ
 - 34 Documents
 - 34 Nebula Monthly Express
 - 85 About Community
 - 96 Security Highlight