[XGS1930] Full CLI access?

MichaelB
MichaelB Posts: 6
First Comment Friend Collector First Anniversary
edited August 2022 in Switch
Hello,

I´d like to get full CLI access on my XGS1930 switch with firmware V4.70(ABHS.1) and local management. Currently if I log with my admin credentials I can only e.g. "show running", but I´m not able to change anything, e.g. "configure terminal" is no possible.

I searched the GUI but haven´t found anything usefull. Is it even possible?

Regards

Best Answers

All Replies

  • Zyxel_Albert
    Zyxel_Albert Posts: 36  Zyxel Employee
    First Answer First Comment Friend Collector Third Anniversary
    edited May 2021 Answer ✓
    Hi @MichaelB

    XGS1930 is a web-managed switch. It only supports web configuration.
    The CLI only allow you to use the "show" command to check switch statistics and table, like: show running-config, show mac address-table all, show interfaces status, etc...

    Reminder: You may use "show ?" to display all commands which can be use with show.

    Regards
  • eddeig
    eddeig Posts: 4  Freshman Member
    First Comment Friend Collector Fifth Anniversary

    Hello,

    I still have a XGS1930 in use. What would you suggest, if I want a new switch with about the same capabilities as the old XGS1930, but WITH full CLI capability?

    Regards,
    Eddeig

  • Zyxel_Melen
    Zyxel_Melen Posts: 2,571  Zyxel Employee
    Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate
    Answer ✓

    Hi @eddeig,

    Since you need full CLI capability, you may consider the XGS2220 series.

    For more information, please reference our website.

    XGS2220 Series - 24/48-port GbE L3 Access Switch with 6 10G Uplink - Overview | Zyxel Networks

    Zyxel Melen


  • eddeig
    eddeig Posts: 4  Freshman Member
    First Comment Friend Collector Fifth Anniversary

    Hello,

    Since we have no full CLI on XGS1930, is there some way to speed up setting up "Time Ranges"?
    So far I have to set each port separate which takes a lot of tome if you have to configure multiple ports.

    Kind regards,
    Eddeig

  • eddeig
    eddeig Posts: 4  Freshman Member
    First Comment Friend Collector Fifth Anniversary
    https://community.zyxel.com/en/discussion/comment/31720#Comment_31720

    By the way… Your datasheet is STILL misleading! See for yourself:
    https://download.zyxel.com/XGS1930-28HP/datasheet/XGS1930-28HP_6.pdf

    It says "Management through Telnet" - you should mention that you do not have full CLI management via Telnet!

    Regards,
    Eddeig

  • Zyxel_Melen
    Zyxel_Melen Posts: 2,571  Zyxel Employee
    Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate
    https://community.zyxel.com/en/discussion/comment/72110#Comment_72110

    Hi @eddeig,

    You can consider using Nebula mode. The Nebula control center allows you to select multiple ports and configure the same PoE schedule.

    By the way… Your datasheet is STILL misleading! See for yourself:
    https://download.zyxel.com/XGS1930-28HP/datasheet/XGS1930-28HP_6.pdf
    It says "Management through Telnet" - you should mention that you do not have full CLI management via Telnet!

    Thanks for your input. Please be assured that I will let our switch product team know your input. In addition, the web-managed switches do not support full CLI. They only support monitoring commands.

    Zyxel Melen


Categories

Switch Help Center

EnglishTiếng ViệtРусскийไทย中文（台灣）