MAC address information on NSG

Zyxel_Freda
Zyxel_Freda Posts: 397  Zyxel Employee
25 Answers First Comment Friend Collector Third Anniversary
edited April 2021 in Nebula

It's an idea from @ComputeInTheCloud that there should be displayed the MAC addresses of all NSG interfaces somewhere on NCC.

Comments

  • mARsIM
    mARsIM Posts: 11  Freshman Member
    First Comment First Anniversary

    Have you implemented this feature?

    It could also be useuful for ATP and USG.

  • Zyxel_Melen
    Zyxel_Melen Posts: 2,577  Zyxel Employee
    Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate

    Hi @mARsIM,

    You can check the MAC address information in site-wide > clients. This page displays the clients connected to AP, Switch, and Firewall/Security Gateway.

    image.png

    Zyxel Melen


  • mARsIM
    mARsIM Posts: 11  Freshman Member
    First Comment First Anniversary

    Hi Melen, ok but where i can see others interfaces MAC?

    For example, one of our ATP has MAC XX:XX:XX:XX:XX:C2 shown in Client List page but if i check in the ports switch details where it's connected, i can see MAC XX:XX:XX:XX:XX:C4 , XX:XX:XX:XX:XX:C5, XX:XX:XX:XX:XX:C6 and there isn't MAC ending with "C2"

    These MAC are not visible under clients list page as you suggested. It's visible only the mac "C2" in that list

    It is important know all MAC for example to setup L2 isolation in SSID guest so it should be better display all interfaces mac address in the firewall page or somewhere in the firewall/interfaces page.

    atp client list.png
    mac table1.png
    mac table2.png
    vlan 99 Switch.png
    vlan10 interface.png

    Thank you!

  • Zyxel_Melen
    Zyxel_Melen Posts: 2,577  Zyxel Employee
    Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate

    Hi @mARsIM,

    Thanks for your feedback~
    Actually, NSG can check the MAC address of each interface/port on the device detailed page. However, ATP and USG FLEX do not support it. May I know if you hope the Nebula displays each interface's MAC address of ATP/USG FLEX on the device detailed page?

    Zyxel Melen


  • mARsIM
    mARsIM Posts: 11  Freshman Member
    First Comment First Anniversary

    Sure Melen, why not?! ;) I think It can be useful for everyone

  • Zyxel_Melen
    Zyxel_Melen Posts: 2,577  Zyxel Employee
    Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate

    Hi @mARsIM

    Thanks for your feedback. I have created the idea post for you. Here's the link of the idea post:

    https://community.zyxel.com/en/discussion/20008/nebula-can-display-the-mac-address-of-all-firewalls-interfaces-ports

    Zyxel Melen


  • mARsIM
    mARsIM Posts: 11  Freshman Member
    First Comment First Anniversary

    Great! Thank you Melen

Categories

Nebula Tips & Tricks


    Read more

    Nebula Help Center

    EnglishTiếng ViệtРусскийไทย中文（台灣）