-
XS3800-28
I used 2 XS3800-28 switches for stacking. Switches have 28 ports, of which 21-28 are combo ports. When stacking, 2 pairs of comboports (25-26, 27-28) become unavailable. Is this normal behavior? How to properly stack on a ring topology: 1) SW1 port 28 - SW2 port 27 SW1 port 27 - SW2 port 27; or 2) SW1 port 28 - SW2 port 28…
-
XGS1250-12 - ability to configure webpage logout time
When configuring either of my Zyxel switches (I have three XGA1250-12), sometimes the page timeout is too short especially when working between the three units and other IT systems and reverting back to a locked page. There seems to be a default of 5-minutes which can be limiting, unproductive and frustrating to use. I'd…
-
SFP+ not connecting to switch GTEK
So bought a XGS1210-12 10gb (inc 2.5gb) switch. Plugged it in to GTEK 10G SFP+ multimode transceivers and nothing. They say they support Zyxel (call out SFP 10G-SR on amazon). Any ideas? All other RJ45 ports work fine but SFP does not get recognised. Also I am a Mac user (sorry have PC buy work so not admin). I cannot log…
-
dhcp offer zyxel xgs-4526
greetings after creating a vlan, enabling a trunk port and enabling dhcp service on a zyxel xgs-4526 switch and establishing the connection with a gs1910 switch via the trunk, the pc connected to a port in access mode on the switch gs1910 not receiving dhcp offer
-
Import HTTPS certificate to Zyxel 1930-10 to avoid ssl error.
Good afternoon. I am trying to install an SSL certificate on my Zyxel switch. As much as I hit the "Import" button within: Maintenance--certificates, it gives error. I generate the self-signed certificate with PFsense in PCKS12 format as indicated in the switch, but nothing happens, it does not work. How can I import a…
-
GS2200-24P Firmware
Requesting latest to be ever released GS2200-24P Firmware.
-
IGMP Snooping and XGS1930-28, XGS1930-28HP, XS1930-10
I have three Zyxel switches, all working in Nebula cloud mode. XGS1930-28HP for my POE devices, XGS1930-28 for the rest devices and XS1930-10 for the high speed (above 1g) devices. I want to enable IGMP snooping since I am using some multicast traffic in my network. The only option I see in Nebula is IGMP snooping enable.…
-
XGS2210-28HP Stacking
Good afternoon I have 2 XGS2210-28HP switches and I want to stack. The manual does not indicate whether it is possible to stack the specified switches in a ring (2 pairs of cables between each switch, i.e. SW1 ports 27, 28 are connected to ports 27, 28 of SW2). It needs to be clarified: is it possible and correct to…
-
DAI allows other source IP on DHCP MAC
So yes might not get this fixed on GS2210-24 V4.50(AAND.4) being EOL but maybe this happens on newer models? So I have a VLAN 50 port 24 to FLEX 200 with a LAG 25-26 as Trusted to internet router FLEX 200 does DHCP IP source guard lists the MAC and IP it got. I then added to FLEX 200 a virtual interface 192.168.100.254/24…
-
XGS Switches and clients disconnecting and then connecting again.
I have a client that has multiple XGS switches throughout their facility. The wiring was done by a professional wiring company a few years back, so it's all new wiring. The client keeps having issues with their device losing network connectivity in the middle of use. When I look at the switch logs, it shows the port going…
-
NSW200-28P Switch
I have an NSW200-28P Switch but when I logon to the admin portal I do not see any links to configure the switch - please refer to the attached screenshot. I want to configure separation between guest and the corporate network so that I can grant non-corporate devices just access to the internet through the guest network.
-
GS1920-24HPv2 - 4.80 Firmware: How Firmware/Configuration go together?
Hello, after I have updated today to 4.80 FIrmware I have seen some optical changes in the UI. My question today is: I have two configurations but only Config 2 is the "good" config for me. Where can I see which firmware is running in Config 2? The currently running config is Config 2, which can be seen under Maintenance →…
-
how to change administrator password swich zyxel xgs-4526
Greetings, I have a zyxel xgs-4526 switch, I want to change the administrator password, thanks.
-
Cisco AP on Zyxel XS1930-12HP (Switch)
I'm having a weird issue with packet loss with a Cisco C9120AXI-E AP connected to my Zyxel XS1930-12HP. Basically, my Zyxel's AP port is set up in what I believe is deemed (VLAN) hybrid mode, where the port connected to the AP has its "VLAN Port Setup" PVID(VLAN) set to the AP Management VLAN e.g. 127, the Acceptable Frame…
-
update gs1900-8 fails updatering firmware
Hello, I need to have updated 4 pcs gs1900-8 but I have firmware 2.7 but it won't take it - it fails in the update, tried version 2.6 same error, tried via zone and http
-
GS1900-10HP Configuration Failure Reset did not work
Hello I wanted to configure my GS1900-10hp switch and therefore i followed this howto to connect to the switch: https://mysupport.zyxel.com/hc/en-us/articles/360008609380--Switch-How-to-configure-the-IP-address-on-a-GS1900-xx-switch-firmware-1-00-to-2-30- Setting the IP from my laptop and i was able to connect to the…
-
GS1900-24HP Fw Ver:V2.70(ABTP.5) & Ubiquiti Bullet M2 Power AP
Hi. Since installing the new GS1900-24HP switch, my two Ubiquiti Bullet M2 Power accesspoints are cut off from the LAN. There is no ping, no transmission from the Wifi client to the network. APs are connected along the way with switch 8port (I checked several switches) and powered by POE power supplies (I checked several)…
-
GS1920-48HP - Port Led Issue and link speed issue
Hi all, is my first post here, so maybe if I get something wrong please tell me. I have a new GS1920-48HP switch, just started the configuration. It needs to run vlan 1 and vlan 20 (used for voice). I am noticing an unusual behavior, if I connect a device (e.g., a phone) to the switch port and then cascade a computer to…
-
snmp
after firmware v480 the SNMP is disable?
-
PC Not Working in Switch>Phone>PC Setup - GS1900-10HP
I have a GS1900-10HP switch that I am trying to configure for a setup like the following. Switch>Phone>PC Switch is on the Default VLAN 1 Phone is on VOIP VLAN 1040 PC is on Data VLAN 4 The phone works fine, however the PC continues to not work. I have double checked the DHCP server address on the switch along with the IPs…
