-
GS2200-24 and GS2200-24P Switch Firmware and MIB File How to find ?
Hello! I have two switches for which the passwords are unknown (GS2200-24 and GS2200-24P). I know that you can download the firmware through the com port. But these devices are not supported (end of life). Where can I find firmware for these devices?
-
Arris SB8200 modem (2G) LAG + pfsense with XGS1250-12
Hello, I feel like this is all so new to me and I'm trying to solve an issue that my current Asus router cannot solve. Long story short is that the WAN aggregate feature on my Asus AXE7800 gets greatly reduced when I connect the 2.5gbe port to the Zyxel switch. I'm getting ready to move to something more flexible such as…
-
Clients connecting to APs through a Zyxel GS1920 not reaching the RADIUS server
I replaced my Cisco switch with a Zyxel GS1920. Figured out all the VLANs and internet is working great. The problem I am running into I have a Network Policy Server (NPS) to authenticate users to an employee network. This worked fine in the old Cisco switch, but now it stopped working. I added the IP to the NPS server and…
-
How to get Zyxel ES3500-24 firmware?
My device always reboot itself, I need a firmware to upload via console. Please kindly help. tks! :)
-
Weird GS1915 series default
As stated by manual: management address is (still the useless limitation to not user-allow copy from PDF manuals… worked around without using Adobe Reader). http://setup.zyxel or http://DHCP-assigned IP or http://192.168.1.1 The latter is the same default address of every Zyxel router and firewall. It seems a bit…
-
Cannot ping anything from GS1920 switch, but can ping from a device on the network
Similar to my last question I have not been able to figure out why I cannot communicate outbound. I cannot ping the gateway IP or anything else. I have the gateway and DNS servers added.
-
GS1915-8 Initial Firmware upgrade stuck
Yesterday I began installing my new switch, choosing to do the firmware upgrade. It is now the following day and the light on the switch is still blinking. How long should it take for the upgrade to be finished? What can I do to fix this since it is not even finished with its installation?
-
XGS1250-12 and SFP+ 10GbE Transceiver compatibility
Hello! I was looking for a managed switch that has at least 4x 1G/2.5G/5G/10G RJ45 ports and 4x-6x 1G (or faster) ports. I came across the XGS1250-12 switch and it is great in terms of cost and features. The only thing I see is that the 4th 10G port is SFP+ and the datasheet doesn't list the SFP10G-T transceiver. When I…
-
Issues with firmware upgrade GS2210
Hello colleagues! I'm having some issues upgrading my GS2210 switches to latest patch 4.50 (AASP 4). So far on 3 switches(2x GS2210-8 and 1x GS2210-24) running 4.50 (AASP 2), when I'm trying to upload the new firmware file, the browser displays uploading percent, but the progress bar doesn't display. Also, the upload ends…
-
GS1900-HP24 help missing after upgrade from 2.6 to V2.70(AAHM.5)
The embeded help is missing from the console management, give broken url message. The application notes stated the help is now web based (as was the previous 2.6 version i think). I rebooted switch twice after firmware update. Any ideas?
-
Help required with a VLAN ZYXEL noob question
Hope some one can help me with configuring VLANs on the below kit, I have the following setup… ZYXEL - VMG8825-T50 ZYXEL - GS1200-8 The router is in the basement and the 8 port switch is in the loft, the gigabit uplink to the loft switch is from LAN1 on the router to port 1 on the eight port switch. Here is my question: I…
-
Configure GS1900-24HP to block internet access for IP Cameras?
I have multiple IP cameras. Is it possible to create a configuration (Virtual Network?) that will block the cameras from accessing the internet? Could I do the same thing by configuring the cameras with a bogus Gateway address? Would this protect cameras from internet probing? Thanks!
-
XGS1250-12 LACP support ?
Hello ! Is it possible to support LACP port aggregation for the XGS1250-12 model? I purchased this model hoping for port aggregation with Synology !!! Are looking forward to !!!
Thank you
-
Zyxel XS3800
Good afternoon. I have 2 XS3800 in stock installed. aggregation is done on 4 ports. T9 port 1/9,2/9, T10 1/10,2/10. They have connected servers on which bond round robin is assembled. When testing iperf from one server to another (from T9 to T10). Traffic from T9 (1/9 -5Gb/s, 2/9-5Gb/s) for some reason goes to…
-
GS1900-24HP Firmware V1.00(AAHM.1) to latest?
Hi, Just purchased an old, now EOL GS1900-24HP. I've reset it and managed to get into the device. It currently is running firmware V1.00(AAHM.1) and I see that latest firmware is 2.70 (AAHM.3).C0. Can I upgrade directly from my current version to the latest or do I have to install other versions first (if so which and what…
-
Any ONU not working in Zyxel OLT-1308S-22
Hello Guys Dose anyone know if there could be another ONU Working in my Zyxel OLT-1308S-22
-
details for GS1900-24EP and GS190024HPV2
Hello, I have a question : The ports are 100/1000 Mbps compatible, are they compatible with 10 Mbps? Thanking you in advance for this clarifications.
-
GS 1900 Firmware Upgrade - 2.70v5 vs 2.70v3 differences
Hope this is not a repeat question. I was hoping someone could point me in the direction. I am upgrading a work switch. The obvious answer to upgrading would be to upgrade to 2.70v5 with no questions asked. I am curious if there is any way to get specifics about my current versions firmware(old 2.20) vs 2.70v5 vs 2.70v3. I…
-
Prevent Auto Logoff on GS1900-24E
I have Zyxel GS1900-24E running V2.70(AAHK.5). I am new to the switch so it takes time for me to administer the switch. While trying to make changes and following videos and/or instructions from internet I get logged off often. Is there away to prevent this from happening? I don't see a way to configure the inactivity…
-
SFP+ 10GBase-T Compatibility and XS1930-10 Questions
I am new to SFP+. I want to add an SFP+ 10GBase-T (RJ-45/Copper) to my XS1930-10 to use at 10Gbps. I tried a 10Gtek and while initially it seemed it was working fine I experience multiple problems. Can you pls share any 10GBase-T that works fine with the XS1930-10? Also, in the port status section, what am I supposed to…
