-
GS1900 V2.70(AAHH.1) firmware
HiI notice the above FW was recently withdrawn from the downloads area. I cannot find any announcement as to why. I upgraded my switch to this firmware some time ago. Should I downgrade to 2.6?Many thanks.
-
Zyxel GS1910-24HP Reset .ROM Firmware
Hi, we have taken over some Zyxel GS1910-24HP switches which need resetting, I followed this tutorial online but need the .ROM software it seems to be able to reset it. I can't find it online if anyone can supply it? Thanks
-
GS2210 Classifier and Policy rules logic
I make the following: --------------- Classifier 1 MAC allow port 19 Source MAC
xx:xx:xx:xx:xx:xx --------------- Classifier 2 Block all
port 19 port 19 --------------- Classifier 3
DHCP_cast_port_19_allow port 19 Destination MAC
ff:ff:ff:ff:ff:ff Source port 68 Destination port 67 ----------------- Classifier…
-
Dynamic VLAN Assignment By MAC Address
Simple setup, VLAN aware router connecting WAN to multiple VLANs on a single managed switch, a Zyxel GS1900-24Right now, the config on the switch needs to know "assign this port to this vlan and incoming packets will be tagged or untagged". From an admin perpective, that is a pain, especially when different devices move…
-
XGS1250-12 - Jumbo Frames / MTU setup
Hi, I am considering buying XGS1250-12 and I can see that it can work with max 12kb jumbo frames. I think I have also seen that there is no control over size of it in the webinterface. Does it mean that jumbo frames will work if I set my devices connected to it to anything lower than 12kb / 12000 MTU? Does anybody have…
-
Have 12 port multi gig . Have 5 gig internet. Which port do I plug internet into the switch?
Do I use port one or do I have to use on of the 10gig ports leaving me with one? Thanks
-
GS1900-24EP VLAN ID does not follow
Hello, I use the GS1900-24EP switch to disptach wifi access points to my firewalls.The GS1900-24EP was put in place to replace an old HP with a management interface outdated.So I know that my configuration is fine.We have 2 VLANs : one for "internal" users (ID : 4) and the other for "gests" (ID : 3).Users are connected…
-
Port going up and down, and cpu utilization over 100
Hello,I think I might have misconfigured something.I have a switch giving me those messages.the model is an eight port GS1920-8HPwith firmwareV4.70(ABKZ.5) NO stp: STP topology changesIN system: CPU utilization is over 100 and keep 5 seconds, driver count = 115. IN system: CPU utilization is over 100 and keep 5 seconds,…
-
Voice VLAN setup conflic with existing voice VLAN.
Hey everyone, I have a few Zyxel switches. One GS2210, and two GS1920's. I am going to use the Voice VLAN Setup for the new phones about to be deployed on site. If I set this up and tie this to the existing voice VLAN, VLAN100, will this cause issues for the current phones on that VLAN. VLAN 100 is currently statically…
-
GS 1910 24 hp config question
I inherited a network system without any info. I manage an apt building. The system has internet coming in to the modem, then it goes into a Juniper WLC100 WLAN controller that is EOL, then it runs into the GS 1910 24 hp. Is the WLAN redundant? Can I eliminate it and just run the feed from the modem or even a router into…
-
XGS1930 Zyxel dac setting suddenly returns to sfp+
Hi all, I have two XGS1930-28 switches connected to a core switch over the 10G uplink connection. This is a DAC cable, and thus so setup in the Nebula control center. However, when I was renaming ports (just the 1G access ports), after the second port, the switch became unavailable causing a network downtime. Local login…
-
Zyxel XS1930-12HP SSH command over libssh (C++)
Hi, I am trying to run the SSH command "show pwr" in my program (C++) via SSH connection. I use the libssh for this. I can see in the system log of the switch that the connection works: "IN authentication: SSH user admin login [IP address = 192.168.0.172]". When I send the command "show pwr" I receive the "unknown error"…
-
Zyxel XS1930-12HP "Consuming Power" over SNMP
Hello experts, I want to query the switch about the "Consuming Power" via SNMP (OID). What would be the OID string for port 4? Best regards Chris
-
GS1900-24 firmware 2.70(AAHL.0)C0 endless login redirects
Hi, I installed a new GS1900-24, original firmware version was V2.60(AAHL.3). I played with the settings for few hours and before final installation updated to GS1900-24_2.70(AAHL.0)C0. After updating to 2.7 when trying to login again after session is timed out, I succeed to login and within 2-3 seconds the web redirects…
-
GS1900-24E
I have set 200 Mbit bandwith limit in Ingress RateLimit but it seems not work, infact the speed rate is too variable and is set to 20 - 30 MBit, and if I try to set Egress RateLimit everything works perfectly!!
-
Switch que cumpla con los siguientes RFC
Switch 24 Puertos PoE Budget de PoE+ mínimo 370 W Debe poseer todos los siguientes: Extensiones TLS (RFC 3546), TLS versión 1.2 (RFC 5246), TLS para Syslog (RFC 5424), (RFC 6125 ), Encripcion TLS para RADIUS (RFC 6614), SSLv2 y SSLv3, RMON (RFC2819), RFC1157, RFC1215, RFC 3411, RFC 3412, RFC 3413, RFC 3414, RFC 3415, RFC…
-
XGS1250-12 cannot change management VID
switch:XGS1250-12, Firmware: V1.00(ABWE.1)C0 Hi, I can enter a new Vlan ID number in the web interface. Apply will force the popup "Switch will be locked out on management VLAN configuration", pressing OK (the only option offered) returns the screen and the VID value is set back to 1. I expect the entered number to stay…
-
VMG4927-B50A random resets
This DSL modem configured in dual dsl mode (fed by 2 different DSL connections) to provide me 30Mb down x 4Mb up. However, it randomly will reset - according to the isp this is due to the download speed exceeding the 30Mb bandwidth. I have thoroughly checked all computers behind the modem and all are clean (virus,…
-
Telekom Magenta TV Receiver + Dell Monitor U2422HE with USB C DisplayPort
I own a magenta TV receiver for IP-TV. Whenever the magenta receiver starts a automated and repeating recording or when you only switch on, the Ethernet connection on my delmonitor/laptop goes wrong. The magenta receiver is attached to another slot on the switch (because other room). In case of Ethernet-Issues on my…
-
Help setting up VLAN and multiple SSID with NWA1123-ACv2 and XGS1250-12
Hello, I have a small network that I'd like to set segregate the traffic using SSIDs and VLANs. Something like this: I have created the VLANs on my firewall and switch, like so (treat VLAN 102 as 201, typo above): Not sure where I can create the wifi AP virtual addresses (gateway for that particular subnet)? What do I set…