-
GS1900-24E Hardware Revisions
Hello, What's the difference between GS1900-24E-EU0101F and GS1900-24E-EU0102F?
-
How to set up GS1900 VLAN's using a non-Zyxel router?
I’m having trouble getting VLANs to work on my Zyxel GS1900-8. In my test situation, the GS1900-8 has 2 ports connected: * On port 1, it’s connected to my Asus router with (highly configurable) Fresh tomato firmware. I have 2 VLAN’s on the router; VLAN2 and VLAN3. Those VLANS works fine together with a Zyxel NAP102 WAP…
-
VLANs not working on GS1900-8
Hi Zyxel community, I’m having trouble getting VLANs to work on my Zyxel GS1900-8. In my (test) situation, the GS1900-8 has 2 ports connected: * On port 1, it’s connected to my Asus router with (highly configurable) Fresh tomato firmware. I have 2 VLAN’s on that router; VLAN2 and VLAN3. Those VLANS works fine together with…
-
[XGS1930] blocks IPv6 RA/ND
Hello, so I replaced an older layer 2 switch with the XGS1930 (firmware V4.70(ABHS.1), local management) and discovered that my clients do not receive any IPv6 addresses any longer. On my uplink router I actually cannot see any IPv6 client addresses any longer on the switchport which the XGS1930 is connected to. The…
-
CR system: 12V voltage value
Hey everyone. I have a customer that is suggesting that their network is briefly up and down multiple times during the day. On looking at the logs the only event that I can't explain is the following power event: 3 Jul 16 14:42:58 CR system: System voltage has recovered to normal state 4 Jul 16 14:42:58 CR system: 12V…
-
Problems with registration
I've got new device VMG3927-B50A. Can't register it with note "cannot find device" even all filled right. any ideas? appreciate!
-
gs1920-24hpv2 non-interactive ssh `invalid command`
Hi when i logged in ssh session and execute `show system-information` - all works fine when i execute `ssh admin@192.168.0.254 show system-information` - Received disconnect from 192.168.0.254 port 22:2: invalid command system-information. Is there any way to make this work?
-
GS-108B v3 and gigabit not working
This is my problem: Router with speed 1Gbps --> switch D-link --> PC goes to 1Gbps same router --> switch D-link --> switch zyxel GS-108B v3 --> same PC with same cable goes to 100M/100M Any idea?
-
ZyXEL GS1900-10HP Switch Configuration
Sehr geehrte Damen und Herren, ich habe das Problem, dass auf den Ports 02, 03, 04, und 05 keine Verbindung möglich ist. Die Verbindungen auf der Firewall/ESX sind richtig angelegt, es funktioniert auch über die SSID über den AP´s (Port 06 und Port 07). Die IP Vergabe wird über DHCP vorgenommen. Ich bekomme auf den Port,…
-
RGS200-12P loses the ability to...forward DHCP requests? & Scheduled restart possible?
Hi Guys, Since 1 or 2 years, we are using multiple RGS200-12P at our location in the production halls. all worked well for the last years, but 1 or 2 month ago i noticed a strange behaviour at 3 (out of ~15) devices. They lost the ability to forward DHCP requests. After a reboot of the switch, connected clients get an IP…
-
Vlan`s zyxel gs1200-5
Hello! Today I came across these switches for the first time and I like their interface. I have the following question. I have two gs1200-5 switches in two different buildings. How to configure vlan`s to be tagged for video traffic for cameras and untagged for office users? And do they support trunk so that, for example,…
-
Switch errors
On a switch (Zyxel GS1350-26HP), where Accespoints (NWA5123-AC) connected, i have sometimes errors.The access points transmit two SSIDs that are assigned to two different VLANs.Can someone narrow down the error more precisely? I didn't find anything through the log files.The Switch is connected to a USG Flex 500, but this…
-
GS1005HP no network and all LED blinking
We have installed two GS1005HP in a SOHO with a PoE Wifi access point connected on each and a couple of wired devices. Since a couple of weeks, one of these has all its LED (power and RJ45) blinking at the same quick rate simultaneously (not activity related). Check video here No power is sent to the Access Point and no…
-
Instabilities with GS1200-8 managed
Simple setup, the Zyxel as switch for PCs and printers behind a very very commonly used internet router. Latest firmware (also tried one version before). Some instabilities: 1. the crucial port with the modem will just sporadically connect with 1GB. It often connects with just 100M. A PC connected directly to the modem…
-
GS1500-24P PoE for Cisco 7960 SIP
Hello All! I've just purchased this used switch, and I have issue powering up Cisco 7960 phones. I have 5 of these phones, and so far I was able to power up only 1. I'm using the B type pinout on Cat5, the blue and brown pair is supplying the power. This 1 working phoneis powering up on each port, the other phones wont…
-
Why are there LAN ports and SFP Ports with same port number?
For example in an 8 port switch, There are SFP ports and lan ports labelled 9 and 10. Why are these 2 ports so "special"? Can these 2 ports be used to plug in AP? What happens if I want to configure sfp port 9 in a certain way but lan port 9 in another way? For example, I want port 9 sfp port as uplink and port 9 lan port…
-
VLAN between GS1900-24HP and GS1910-24
Hi!I have a GS1910-24 where i've set the default vlan 1 untagged, and a tagged VLAN id 30, i've put some access points with guest vlan on 30 (tagged), and a router with dhcp also on that vlan. On this switch all works as it should, both vlans (1 default untagged and 30 tagged) works correctly.The config is (for all the…
-
Unable to restore factory defaults on XGS1930-28
I've done almost everything. Reseted with factory defaults with 3,4, 10 seconds. Nothing helped, it seems switch is not resetting to default values. Tryied with myZexel. I receive message device already registered. Where I should go from here to recover access to my device?
-
Switch off Ports by time on XGS1930
Is it possible to switch off Ports for a time on a XGS1930 switch? Regards Bernd
-
XGS1250-12 very very very slow
I have the above switch, connected to my network, the link to rest f the network is 1Gig i have main desktop win 10 machine and a qnap 872 nas both connected on 10Gig ports and happily works for the past 2 -3 months yesterday suddenly the windows machine and access to the nas became almost none existent have done a factory…