-
GS1500-24P PoE
Hello, I have just purchased this switch, I was so excited before the purchase, but now just little frustrated. Maybe I'm just doing something wrong....I do have more than a basic networking knowledge and I hope the issue I'm facing is setting related.So, I have few Cisco 7960 IP phones with SIP firmware. As of now the…
-
Zyxel GS1920v2
Hallo, ich habe am Switch GS1920 den Smart3 der Telekom an LAN 1 angeschlossen. Im Log steht immer "Broadcast storm detected on port 1 - Port1." oder "Multicast storm detected on port 1 - Port1. Ist dies normal? Gruß Marcus
-
GS1900-8HP and GS1920-24HPv2 LACP problem
Hi, I have a GS1900-8HP switch and a GS1920-24HPv2 switch.I made a LACP configuration between the 2, with port 7-8 and port 27-28 respectively.The configuration is seen and is also in "up", but I cannot ping switch 24 from switch 8 and vice versa; also the resources on 8 vs 24 and vice versa are not seen. Where am I wrong?…
-
Do Zyxel have routing capabilities in the 10Gb switches?
Looking for a Zyxel alternative to Cisco ASR901
-
VLAN set up issue on GS1920
Hi All, I have the following set up: MES3500 fiber switch and few GS1920s connected to it over fiber and one GS1920 connected via Ethernet on port 0/26. All the switches have default VLAN 1 which is working fine. I wanted to add VLAN 100. Please see below the network diagram. The issue I have is that from switch sw-fr-01 I…
-
Cheap Gigabit Switch With VLAN Capabilities
On a shoestring budget, I have a number of device that support VLANs that I'd like to segment, plus I'd like to open a wifi network with captive portal secured away from my main network. What I need, though, is a cheap gigabit VLAN configurable switch. Where should I be looking for such an item? Realistically, I only need…
-
Noob question gs1920-48
Just inherited 15 gs1920-48 switches never seen before never used before. I can see them all but no idea how to configure them need the equipment behind them to have access to the internet where do I start I found the utility but still need to understand how to configure them to allow traffic
-
10g Copper SFP+
We recently purchased about 25 Zyxel switches and love them so far. One issue is perplexing me though... We have several of the XS1930-10 switches with 8 copper ports capable of up to 10g. We also have some XGS1930 series switches we would like to downlink from the XS over 10g copper. As the XGS only has sfp+ for 10g, I…
-
GBIC compatibility with XGS series switches
Does anyone have experience with which switch brand compatibility works best with Zyxel other than the Zyxel gbics themselves? I'm not opposed to buying Zyxel gbics themselves, but getting them in a quick manner from local distributor is another matter. I also read that Zyxel doesn't have a SFP+ 10g copper module. I've…
-
GS1900-48HP Voice VLAN stopped working after firmware upgrade. . .
Zyxel GS1900-48HP Rev A1 Moving from firmware 2.60(AAH0.1)CO to firmware 2.60(AAH0.2)CO caused issues with a previously working OUI / Voice VLAN. Specifically - With firmware 2.60(AAH0.1)CO, we had the following VLAN details in place on several ports - VLAN1 Untagged (Default) VLAN2 Excluded (Voice) VLAN3 Tagged VLAN4…
-
Vlan for GS1920-24HPv2
Hi everyone, I have 5 GS1920-24 switches connected together in lacp with ports 25 26 27 and 28. In the company I have a Huawei router where 2 cables, data and voice start, without Vlan; the data cable acts as a dhcp server on the 192.168.1.x subnet while the voice cable acts as a dhcp server on the 192.168.7.x subnet. Now…
-
GS1920-24 stuck in self-diagnostics
Hello, I have a GS1920-24 switch that is now stuck in self-diagnostics mode. The PWR LED is solid, and the SYS LED is blinking. I can't get any response on any port (link down), and it's been running for a few hours like that. The problem started to happen after a power cycle. What can I do?
-
GS1005HP no network and all LED blinking?
We have installed two GS1005HP in a SOHO with a PoE Wifi access point connected on each and a couple of wired devices. Since a couple of weeks, one of these has all its LED (power and RJ45) blinking at the same quick rate simultaneously (not activity related). No power is sent to the Access Point and no network on the two…
-
Noob question. GS1920-48 Inherited 15 of these
I have. 15 of these GS1920-48 i can see them but the hardware behind all of them cannot access the internet where do I start
-
Latest firmware update 2.60(AAHK.3) Gs1900-24E reset to factory default settings.
Why firmware update v. 2.40(AAHK.1) to 2.4(AAHK.3) reset switch to factory default settings?Also history of "Port Counters" and "Bandwidth Utilization" has gone.
-
XGS1210-12 disable QOS
Is there a way to turn off QOS settings alltogether?
-
QinQ and non-stacked (single tagged) packets on a port; zyxel 3700
I have CLI access access only to a 3700-24. It is in a live environment and so I cant experiment with it. Up until now all ports in use have been non QInQ vlan tagged. I now have a more complex setup coming along. One port lets say 1 will bring in a QinQ packet. Lets say 999 on the outer and 888 on the innner. I need to…
-
Switch GS1920-24 - low lan speed
Hello. Few days ago I've swapped my TP-Link gigabit switch with GS1920-24. Everything else remains the same, cabling, devices etc. With TP-Link I was getting full gigabit speed between clients. With new setup, I'm only able to get 300Mb+. Switch is after factory reset and only one configuration change - I have one vlan…
-
2 vlan on xgs1930 + internet without USG
Hello I have an internet box (without vlan management) + 1 Switch xgs1930-52. I have configured 2 vlan (vlan 1 and vlan 2) on my xgs1930-52. The PCs in the 2 vlan must not be able to see each other but they must be able to go on the Internet. All this without USG (router / firewall) How should I do ?thank you in advance
-
Can I use an ES-105A v3 as a Power over Ethernet Switch
I want to use an ES-105A v3 as a Power over Ethernet switch between my router and an external camera