-
GS1900-24HP VLAN PORT SETTINGS - (BROWSER ISSUE )
Hi there Trying to set up a port to use VLAN 1 as the untagged Default Vlan and pass VLAN 100 as tagged frames (trunk port ) Browser has missuing "TEXT " next to the buttons - see below and I just need to know what the labels / test for each button is so that I can configure it correctly I know the browser issue is fixed…
-
XGS1250-12 - all 10G ports are not working after short power outage
Seems that with my XGS1250-12 I just faced the same issue as described here https://community.zyxel.com/en/discussion/14655/xgs1250-12-port-9-and-10-dont-work-after-power-down. More precisely last night there was a short power outage and in the morning I found that all 10G ports were not usable anymore, although just one…
-
Does the GS1200-8HPv2 have the possibility of assigning 2 DHCP subnets?
I have a GS1200-8HPv2 and I would like to know if this switch has the possibility of assigning various DHCP subnets depending on the VLAN that the client connects to?
-
Zyxel XS1930-10 Visio Shapes
Hi, where i can find Visio Shapes for XS1930-10 Switch? I need to create professional Network-Layout within Visio. Thanks Daniel
-
XMG1915-10E & TP-link TX401
Hi All, I have recurrent issues where the switch disconnects the network card, and it happens both under windows 11 and Linux. Bandwith control, loop, storm, port isolation and flow are disabled for this port, RTSP, LLDP, Link are enabled, 10G forced (auto before still with issue). Logs are quite scarce, here is what I…
-
Slow web-interface in standalone mode
Hello, i bought an XMG1915-18EP. Its web-interface is very slow so that configuing is nealy impossible. It takes seconds to minutes until the dashboard appears. I did not change anything from factory defaults exept passwort and disabling Nebular Cloud. Tested with different browsers (Firefox / Edge) on different computers.…
-
Cannot connect to VLAN via AP
I have an NWA50AX AP connected to a GS1200-8HPv2 switch. The AP has 2 SSIDs, one for office and another for guests. I have configured the office SSID as VLAN 1 and guest SSID to be on VLAN2. The port the AP is connect on has both VLAN 1 and 2 as ingress. I can connect to the office SSID but the guest SSID (VLAN2) just sits…
-
XGS-4728F Most recent Firmware
Hello,İ couldn't find any recent firmware for my device can you send me latest firmware from here. Thanks for support
-
Dante (&Nebula)
What switches are currently recommended for Dante use? It is still 1930 and 2220? GS2220 can do two port stacking. Would that work with Dante/IGMP? It it possible to mange Dante-relevant IGMP-settings in Nebula? I would really love to be able to use Nebula for easier remote control of HoW's with this kind of install.
-
GS1920 Switch not booting correctly
Hello, my GS1920-24HPv2 stopped working on x-mas…. Everything seemed to work until 12.00 am, then everything went offline. I checked the switch and pwr/sys were green. Cloud was blinking amber. I was a bit confused because I had disabled the Cloud Feature as I am not using it. So i rebooted the switch to see if it works…
-
GS1900 24HP - Configure VLAN and LAG interface
Hello ! I was given this switch for Christmas and, as I'm still a networking student, I haven't mastered everything, so I could really use your help. Here's my architecture: OPNSense (Port 1/LAN) → SG1900 (Port 1) OPNSense (Ports 3&4) → SG1900 (Ports 23&24) SG1900 (Port 9) → PC (DHCP Enabled) I wanted to make sure that…
-
Switch GS1920-24 where to find saved configuration?
When I press the button at top/righthandside "SAVE", it says after showing a progressbar: "Save configuration successfully." But neither a file into the win10 Downloads folder was saved, nor a dialog to ask me where to save it appeared. Where can I find now the saved config file?
-
EEE / Green Ethernet
Hi If I use a switch like GS1915-8 in Nebula-mode, I can't control EEE/Green Ethernet. Will it be enabled or disabled by default in NEbula mode?
-
Internet radio buffers forever: IGMP problems?
I have a Magenta TV receiver from Deutsche Telekom that requires IGMP. Now I have the effect that when the receiver is running, regardless of whether a channel is being watched at that moment or a program is being recorded in its absence, the Internet radio in the bathroom buffers for seconds, then plays a radio program…
-
Doubling the bandwidth of the link between switches series1920
Dear all, I based the network backbone on zyxel1920 switches. Due to the high load on the network, is it possible to double the bandwidth by connecting two switches using two parallel 1GBps links? (where to look for such a configuration). Is it possible to configure a network with a ring on these switches (each switch…
-
Static LAG VLAN membership
Hi there! I have a brand new XMG1915-18EP switch. I have 3 VLANS, users, guests and IoT. I set the port 17 and 18 as a static LAG with source and destination IP address protocol to another switch. I want to do the following setup: user vlan: untagged ports 11-15 and tagged on lag guests vlan: untagged port 16 and tagged on…
-
Correct Port Settings for a Sky Q box?
Hi! Wondered if anyone could help. I have a small home network, with a sky router connected to the phone line giving me 35Mbps broadband speed (no fibre here!). The Wi-Fi on this router is switched off. I then have two GS1915 switches and two NWA50AX WAPs providing Wi-Fi coverage around my house, and hardwired connections…
-
need Help for XGS4700-48F bottloop
Hello Community, our XGS4700-48F is in a booting loop. I think they forgot the default config. I´ve tested many time to send my config and Firmeare via Xmodem to the device. evrytime i get the Error "Received file size Error" Have any one an idea? Thanks for answers.
-
XMG1915-10EP - POE / PD is interrupted when booting
Hi, I have noticed, that switch when booting is performing 2 or 3 restarts of POE (power delivery is interrupted and resumed). I would like to ask - is there any way to avoid such a situation? This is unfortunately causing that some of my SBCs etc. devices are powered up and forcibly powered off, then powered up, and…
-
GS1200-8 Webinterface behind nginx reverse proxy
I'm running a local nginx reverse proxy as gateway between my home network and the management network. The switch webinterface is reachable from the management network, the Idea is to use nginx to have secure access to the switches webinterface from the home network. This is my nginx config: #/etc/nginx/conf.d/switch.conf;…