-
Switch MG-108 für Games brauchbar ?
Hallo zusammen, ich habe ein Netzwerk das mit 3 Zyxel Switch MG-108 betrieben wird , an einer 10 GB Internet Verbindung. Vom 10 GB Router gehe ich direkt auf 2 MG-108 die als Hauptverteiler stehen von da geht es unteranderem in unser Büro und Gaming raum auf einen weiteren MG-108 von dem aus es weiter auf 2 PC`s und andere…
-
GS1910-24 VLAN Not Working
Hello, Before I address my issue I would like to tell that I am not a switch specialist at all and that many of the articles listed here in the forum confused me. The switch GUI often seems to differ from SW version to version, many of the screenshots discussed here are not available on my devices. Thus I decided to…
-
[XGS1930] Full CLI access?
Hello, I´d like to get full CLI access on my XGS1930 switch with firmware V4.70(ABHS.1) and local management. Currently if I log with my admin credentials I can only e.g. "show running", but I´m not able to change anything, e.g. "configure terminal" is no possible. I searched the GUI but haven´t found anything usefull. Is…
-
Is it possible to show fiber optics info on XS1930-12HP?
I have an old Netgear prosafe switch. On it I can run… Is it possible to in some way show such info on this XS1930-12HP if moving these SFP+ units fromt the netgear to the zyxel switch? I have Access L3 license. Thanks in advance //Peo
-
Managing VLANs?
Hello, I'm trying to separate 2 VLANs that shouldn't be accessible from one another. Port 1 is the uplink, port 2 a PC on port 8 I'm planning to use a laptop that should have access to the internet, but it doesn't (it gets IP, so I'm half there). This is what I came up with:
-
Missing CLI commands on XS1930-12HP
Hi I am new to this forum. Have used an old zyxel switch before, but now I am back on zyxel again. Just bought an XS1930-12HP. I have just installed it and done some test by configuring some VLAN trunks and other stuff. Seems to work as expected. Interesting that it takes 5-10% CPU when idling though… I have bought and…
-
Zyxel GS1900-24e Original firmware
I recently got hold of a decommissioned Zyxel GS1900-24E from a E-waste recycler, but this switch has been modified to run OpenWrt. Is it possible to return this switch back to factory firmware? I've checked the other boot partition, but it seems to have been wiped. Thanks, Dim
-
Weird Login Screen and Can't Access XGS1930-28HP
Hello, I purchased a brand new XGS1930-28HP switch and am experiencing weird issues with it. Upon removing it from the packaging I placed it on the bench, connected a laptop, and powered it up. After the port LED lit up, I connected to the default IP and tried to log in. It wouldn't take the default password. Tried it a…
-
wifi issue unable to connect it just displaying obtaining or connecting
kindly help me to resolve this issue, i am thinking that its vlan configuration error that device not picking up the ip? its controller or switch issue?
-
Struggling to get VLAN to work
-
GS1900 tagged VLAN nodes drop off after 5 minutes
Hello all. I have a very simple test lab set up, a GS1900-24 with a Win 10 and a Win 11 laptop continuously pinging each other. On the tagged VLAN, these pings just stop after 5 minutes, and the only way to get them talking again is to reset (change, then change back) their VLAN IDs in Windows Network adapter settings.…
-
Xs1930-10 flow control?
Hi. I recently bought an xs1930-10. I'm trying to establish what the default firmware setting is with regards to flow control. I can't see it in any menus on the port setup and I asked support via a question but didn't get a answer either. Does anybody know if its on or off or doesn't exist on default setup? I have…
-
Configure the switch to perform DHCP service in a VLAN
Hello everyone! I have a Zyxel GS1920-24. I want to configure the switch to perform DHCP service in a VLAN as in the following link - How to configure the switch to perform DHCP service in a VLAN — Zyxel Community But I can't configure the DHCP service. Any ideas why or how I can do this? I don't have the same option as in…
-
zixel 1250
good morning, just today I installed the latest version of the firmware available that should turn off the LEDs in eco mode and enable the smart auto fan after rebooting I enter the switch management and see that I can turn off the LEDs with eco mode but the option of the fan from auto to continuous forcing is not…
-
ZYXEL SWITCH XS3900-48F firmware needed
Hi, I am a happy user of the XS3900-48Frecently I made some confiuration changes and probable unfortunatelly experienced a firmware fault or deletion from partition in switch memory. I am trying to copy the firmware to the switch over console as I successfully did it with my other switches in the past couple times, but the…
-
Dead ethernet port (port 4) on ZX1930-12HP switch
Hello, My newly installed ZX1930-12HP seems to have a dead ethernet port (port 4). It will not establish link at all, even though if I take the same patch cable and plug it into the adjacent port (port 5), link is established immediately. I pulled the full set of tech support logs, but there is nothing indicating an issue…
-
Mounting Brackets for GS1920
Hello I am looking for rack brackets for my GS1920-48. Used ones for a small budget would be appreciated. Where can I get a pair?
-
Switch problem - SYS
Good afternoon, I have a new Zyxel switch that, when started, keeps the SYS flashing green non-stop and does nothing else. It does not turn on any port. The firmware cannot be updated because it does not detect any connections. How should I proceed?The model is GS1920-8HP. Greetings
-
XS1930-10 rack kit needed
Hi, I need to mount a XS1930-10 in a 19" rack, but at some point the mounting kit has been disposed of. Neither support or I can locate a spare kit and official RMA don't seem to have any, so: * Does anyone have the kit's part number? * Do any other ( easily available ) kits fit it, OEM or no? * Are there any drawings of…
-
Am I missing something obvious?
I just unboxed a shiny new XMG1930-30 switch for home use and my experience in the first hour is… well, less than optimal. My Cisco knowledge is a little outdated but I do hold some cisco certifications so this stuff isn't exactly new to me. So far, I have two major issues. When hooked up to the network, the switch gets…
