-
Low performance on NWA50AX
Hi! I recently installed a single NWA50AX for a client. After successful deployment I went and tested the speed. While I did not expect for Wifi speeds to reach 1Gbps I was quite surprised to see that speed measurements showed speed of max 400Mbps. Configuration: -1st NWA50AX - Wifi settings: BSSID on 5GHz @80 MHz(2.4Ghz…
-
NWA90AW Which SSID is 2.4G / 5G
Hi I have just purchased a NWA90AW, however I don't know which SSID is which Need to label them as 2.4G and 5G on the broadcast How do I tell which is which from this screenshot I guessed the SSID1 would be the 2.4G and the SSID2 the 5G, but download speed appears to be the same
-
NXC2500 high CPU usage / Sessions
Hey there, i have a NXC2500 and 5 NWA5123-AC for 5 years and it works great. But since a few weeks the CPU Usage from the NXC2500 goes up to 100%. I can see that the Session count is between 2k and 10k and then the CPU usage is very high. But i cant find a solution and hope you can help me. The Firmware from the NXC2500 is…
-
NWA1123-NI has the wrong firmware and will not accept new firmware
I have uploaded firmware version V211AABJ0C0.bin (belonging to a NWA1121-NI) to my NWA1123-NI. The web interface demonstrates that it thinks it is an NWA1121-NI. It works a little, but often loses all connections. I was hoping that updating the firmware to the correct one (V211AAEO0C0.bin) will correct the issues, but I…
-
Lost access to AP's SSID setup in Nebula
I started setting up 5 new access points (NWA50AX) a couple days ago. I was able to configure them in Nebula, but now I cannot get to any SSID configuration options in Nebula. If I go to the Wifi SSID settings page, it tells me I need to add at least on SSID. If I click on the "advanced mode" slider, it gives me the…
-
NWA50AX Pro - NWA90AX Pro differences
What are the differences in features/performance between those two APs? I couldn't find information about it. Specs seem to be same.
-
LLDPD is Dead NWA210AX (Rebooting every 15 min)
After last nights weekly reboot I'mm getting this error in the logs and my APs are rebooting themselves every 15 minutes……. This is in the log just before reboot happens: 2023-11-25 23:51:59 alert System lldpd is dead at Sat Nov 25 23:51:59 2023 App Watch Dog 2 2023-11-25 23:51:59 alert System App watch dog stop to recover…
-
nwa50ax keeps showing offline . HELP
Hi I have 3 NWA50AX WAP's all powered POE switch via Lan cable . One of them has started going offline . The other 2 are fine . I also see the the one that goes offline when it comes back up it shows it is Uplink: 100M/Full. Not Uplink: 1000M/Full. like the other 2 Any ideas? This is the status of the problem one This the…
-
NWA90AX VLAN
Hi I have 2 SSIDs Im broadcasting on 2 vlans 20 and 60. The switch is a HP2930F running 16.11.0014. The APs are NWA90AX. If I plug a laptop into the same port the AP plugs into I get the proper DHCP and access to the internet. I can connect on vlan 60 wifi with internet but loop " connection lost" on 20. Event logs say…
-
NWA220AX-6E dropped packet
Hello, I have some bad interface statistics: Router> debug interface ifconfig … wifi0 Link encap:UNSPEC HWaddr 78-C5-7D-7B-ED-BC-00-00-00-00-00-00-00-00-00-00 UP BROADCAST RUNNING MULTICAST MTU:1500 RX packets:5257733 errors:24 dropped:3 overruns:0 frame:0 TX packets:7951690 errors:1659 dropped:1659 overruns:0 carrier:0…
-
Bluetooth Low Energy (BLE)
I wonder if there is any Zyxel Unified Pro AP with BLE support? If no one, when do you think BLE AP will be available? Thanks.
-
NWA55AXE - Only as repeater
Hello, i got a consumer class wifi router (wind3 hub H389Xv11) witch worked pretty well with 2 WX3100-TO smart mesh range extenders (autoconfig). I bought this product because i want to cover with a good signal the outdoors with a product with waterproof proficiency. I simply want to extend (without specific performance…
-
WRE6505 no v2
Where I can found the latest firmware for WRE6505 no v2? Grazie Francesco
-
NWA1123-AC-HD old firmware from 2021
Dear users, I use an NWA1123-AC-HD with the firmware V6.25 ABIN.9 of 03/2022 but I have some trouble and I want to try if this is less the problem in the former firmware. If I am right, there should be a firmware from Sept oder Oct of 2021. Is there a way downloading such old firmware-versions on the Zyxel-Homepage (which…
-
UAG 4100 integration with IDS Hotel management software.
can anyone integrate IDS Hotel Management Software with UAG 4100 for wifi authentication?so we can put room no as user and last name as password.
-
[Campaign] Zyxel Network Detective - Case #2 is OPEN! (Answer Revealed)
Detecting a WiFi Network Error Hi, all tech enthusiasts! After the tremendous success of our Case #1: Crack the for Switch challenge, we are happy to announce our next epic adventure, Case #2: Crack the Case for WiFi Network. If you enjoyed uncovering network errors in our previous challenge, get ready for a new and…
-
Weird delay with WAX640S-6E
So for personal use I picked up one of these when the priced dropped. Overall love the unit it preforms well and and has great coverage even as just a single AP. Not on nebula and working in stand alone mode. Using firmware 6.60(ACCM.2)C0 and powered with the Zyxel 2.5gb Poe injector The problem I'm noticing is sometimes…
-
no IP by assign the corresponding VLAN
My environment: FritzBox → GS1920-24HPv2 → AP NW-1123-AC-PRO. My goal is to setup up one Guest-WLAN and one WLAN for my other devices in the network. I´ve created in the Switch three VLANS: 1-Trunk for connecting AP´s 10- My own devices (SSID USER_NW) 20-Guests The AP is connected to Port 2 and assigned to PVID-1 In the AP…
-
How to configure SSID Private and public WAC500
Hello, I would like to know if it's possible with the WAC 500 in standalone mode to make 2 SSID. Exemple : Private for all users in the company 192.168.x.x Public for the external users 172.16.x.x The step to create the two SSID is quite easy but the two SSID get the same DHCP… I try to change the ID VLAN on the Public…
-
Captive portal to welcome page only
Hi all, On a NX2500, on the specific SSID protected with password, when users joins this network I'd like to redirect them to a welcome page without to have to sign in. Is there a way to do this?
