-
Guide - Wi-Fi design best practices for multi-floor residential homes
A practical, field-tested guide for reliable whole-house coverage, the way I do it. Reliable Wi-Fi in a multi-floor house is not achieved by “maximum power everywhere,” but by balanced, structured access point design. This guide outlines the recommended placement, configuration, power tuning, and verification process for a…
-
Station blocked by key handshake fail right before connected (intra roaming) - normal behavior?
Every intra roaming (e.g. 2.4>5GHz) goes like this (log, reverse order): 31 2025-11-05 17:21:29 notice wlan IEEE 802.11 Station: 12:34:56:78:9a:be connected on Channel: 36, SSID: MyWifi, 5GHz, Signal: -66dBm, Interface: wlan-2-1 32 2025-11-05 17:21:28 notice wlan IEEE 802.11 Station: 12:34:56:78:9a:be blocked by key…
-
On my FWA510 I have made a new SSID but it is not working?
-
WBE660s fail to update the firmware 7.10 to 7.20
Happy owner of a WBE600s AP, it is impossible to update the firmware to its latest version! In add, I noticed on the forum that some users were having difficulties with version 7.20.When is it? Should I wait for a new patch?Why can't I install 7.20? Thanks in advance for your answers.
-
NWA50 AX PRO - Cannot Upgrade from Standalone Drivers which limit connectivity?
Originally setup as standalone device. Following initial enquiry as regards AP restricted to sub 10Mbps up and down with average Ping times of 11.25ms. Human engineer responded last week, " have reviewed the Nebula settings and made some adjustments to improve the wireless connection. Please check the updated status once…
-
NWA130BE / Unable to configure band steering
Hi, I'm following up on a support ticket https://mysupport.zyxel.com/hc/requests/533878 - the technician suggested I followup here since they were unable to help me (and apparently have no way of engaging developers and Tier 3 support?!).. Anyway, I'm reaching out to get help with enabling band steering on my standalone…
-
How can i reset a wax620 to factory defaut
I got an use one with no information over it, how can i reset it to factory default.
-
Link aggregation with NWA220AX-6E
Hi, I can't find a way to setup an aggregate with the two ethernet interfaces in either webui or cli. Is it possible with this model? Thanks, jmw
-
Zyxel nwa130be Problem with Mikrotik wap lr8 Station Mode
Hello, I keep having problems with a Mikrotik wap lr8 device that is connected to the nwa130be. According to the Nebula app, the device is connected to the Wi-Fi and also has an IP address. But after a few hours, I can no longer access the web interface of the Mikrotik device. I have already performed various firmware…
-
DCS Bug?
I have a few Flex 200H on APC version 7.25.2 and WBE530 APs (on 7.20.3). I've seen several instances where DCS doesn't seem to work correctly. It will select conflicting channels when an AP boots up. Manually selecting DCS will cause a few APs to both switch to the same channel (like they are not coordinating). On 2.4GHz…
-
Not a question - The "Register" button is not correctly configured
Hello, I wanted to register via the button (https://community.zyxel.com/en/entry/register?target=https%3A%2F%2Fcommunity.zyxel.com%2Fen%2Fcategories%2Fwireless) the result is a JSON error : detail 0 loc 0 "query" 1 "SAMLRequest" msg "field required" type "value_error.missing" I connected using my Google account but would…
-
NWA110BE enable MLO on 2.4 Band
NWA110BE [RMID: 62239] [Symptom] The access point may reboot unexpectedly when the 4GHz radio is configured in BE mode. To prevent this, the 4GHz radio mode has been converted to AX mode. 2.4Ghz Radio broadcasts in AX mode when configured to BE mode Log shows MLO disabled: reason unsupported radio mode option How to…
-
NWA50AX and NWA1123 AC
Hi everyone, I have a Zyxel NWA1123 AC, and these two features are very useful: An antenna button, to allow for ceiling or wall installation, changing the antenna radiation from vertical to horizontal depending on the access point's positioning. An Ethernet output port for extending the network via cable. The new NWA50AX…
-
Flex H AP Controller Release Notes
Where can I find the release notes for the Flex H AP controller firmware? I see it just updated from 7.20.2 to 7.25.2 but clicking "More Detail" just takes me to the general AP controller overview.
-
NWA50ax Pro - Decrease transmission power at night
Hi! I just bought an NWA50ax Pro AP and started to set it up (in Standalone Mode). I would like to lower the transmission power of the 2.4G radio and turn off the 5G Radio at night. The AP is operating in a private hause and it's not necessary to have full power over night. How can I achieve this? Thanks.
-
Controller AP Group Function
What function to do the AP groups serve on the Flex H AP controllers? Is roaming limited to APs within a group? I have several APs in a building and one of them serves an older b/g IOT device. I'd like to put this one in a separate group with the older functionality enabled (control rate <11 Mbps, and ax/ac/n station only…
-
[NWA130BE] - MIB Files for SNMP Protocol
Hello everyone, I see that is possible to enable the SNMP Protocol for the AP in object. Can I have access to the MIB Files for the private SNMP OID? Thank you
-
how do I setup different schedules on different SSID's from the same AP
-
WLAN unstable and kernal panic after Update clients to IOS/MacOS26
Hi, i use a WBE660s on latest firmware. After Patch 7.20P2 the AP runs without any problems for a while. After updating to IOS 26 and MacOS 26 the AP becomes unstable. Every aprox 24h the 26-Clients could not connect to wlan anymore. After disabling and enabling SSID in Nebula-App it works fine. Last night i see 2 reboots…
-
Router 5G NR-5103Ev2 and Multy M1
It is possible to connect this router with the Multy M1 to create a mesh network? Thank you
