-
WBE660S will not connect to other devices on 5ghz radio
I have been trying to track this down of why randomly I couldn't access other local devices. I have a TP Link Wireless Extender and a Reolink Wifi Doorbell. If I connect via 2.4ghz radio or the 6ghz radio both apps on my phone will find the devices. Tether App for TP Link and Reolink for Reolink Wifi Doorbell using Apple…
-
Howto Import SSL Certificate into NWA50ax Pro
I am trying to install an SSL certificate on my Zyxel NWA50AX Pro. I’m running firmware v6.65(1). When I go to: Configuration>Object>Certificate>My Certificates>Import, it gives error: errno: -13011 errmsg: PKI certificate type is not supported. I generated the self-signed certificate with PFsense in PCKS12 format. The…
-
Optimizing Wi-Fi Performance with Zyxel Access Points
Hey everyone, I recently installed a Zyxel access point to improve the Wi-Fi coverage in my home or office, and I'm looking for tips on how to optimize its performance. While the coverage has improved, I want to ensure that I'm getting the best possible speed and reliability from my wireless network. Does anyone have any…
-
It is possible to restore the NWA5123-AC-HD device
https://us.v-cdn.net/6029482/uploads/5WV9CV9IUQI3/putty.log Hello After an unsuccessful device reset. Is it possible to restore the equipment? I am attaching the log file. when entering commands it gives an error
-
How to connect usb-ttl 4-pin wire
Hello Tell me how to connect the wire to the console on the zyxel NWA5123-ac-hd? found an article https://community.zyxel.com/en/discussion/3857/console-port I understand correctly what needs to be connected: 1 pin white 2 pin green 3 pin black 4 pin (with track pad) red
-
NWA50AX speed
My AP's don't work as they should. My wired speed from modem is 900/1000Mbit/sec., but when I am on 2.4ghz WiFi through an AP (NWA50AX), speed starts at 50/60/70Mbit, but lowers sometimes even to 10Mbit. So not even close to what it could be. At 2,4Ghz, 200/300mbit must be possible. Or even if it was a 100Mbit stable, I…
-
WEP security of obsolete SoundBridge device and AP NWA-1123-ACv2
Good day, I have a "somewhat" older piece of HW - specifically, the SoundBridge M1000 radio, which, after being equipped with a wireless CF card, is also capable of wireless connection. Unfortunately, the only possible wifi security (besides the MAC filter) is WEP encryption. I understand that it is already very outdated…
-
Zyxel NWA 210 Audable on Load
Hello, following strange behaviour on my new and now third NWA 210: During load, e.g. a Speedtest, I can hear the AP. Sounds like Coil Whine. It is audable from 10 feet away, and in a quiet room its a bit distracting. This happens only, on the 5 GHz Band (note channel width 160 MHz) I will try to test with 80 MHz and…
-
NWA50AX Not able to manage via standalone
Hi all, Recently purchased an NWA50AX. I am not able to get to the standalone management page in order to do any settings or change ssid's. Plugging in only power, the device eventually goes into the "Discovering NCC" stage (slow blinking orange and green). At this point, I either try to connect to the broadcasted ssid…
-
Nwa1123-ACV2
Hi. Does thie AP support wireless client mode so I can attach a printer to the network interface and use it wireless? I can't seem to find the operating mode "wireless client" in the settings. Firmware is updated.
-
NXC5500 - Firmware update
I want to update my ZyXel NXC 5500 -Boot module: V1.04 -Current version: V5.00(AAOS.3) -Release date: 2017-02-03 I can't find the firmware update documents.
-
Why can't I set a static DHCP
I have recently acquire a raspberry pi and want to make the IP address static. I logged into my router settings by typing in the devices IP address into Chrome. In the settings, under home networking, when I try to set the device as static DHCP I get an error message "Warning: Need to disconnect/connect the device or…
-
Zyxel NWA 210 Dead ?
Hello, it seems my Wireless AP Zyxel NWA 210 died. No LED, either on PoE or on DC. Also a high pitched noise (coil whine is my best quess) on PoE. While switch shows only PoE but no connection . Help would be appreciated. Best Regards Felx Schneider
-
About NWA210AX WDS issue
Hi, I have a question about NWA210AX WDS function: Can NWA210AX WDS support to wireless connect to a router which support WDS too? like: Internet - Router (support WDS) - (wireless) NWA210AX or NWA210AX can only support Ethernet to router and like: Internet - Router (support WDS) - (Ethernet) NWA210AX - (wireless) NWA210AX
-
NWA55AXE TWT activation
I've brought a NWA55AXE and twt was working at the begining. After an update its not working anymore. Where can i download the older firmwares or how can I activate twt? Im very disappointed!!!
-
NTP is incorrect
Hello, I've noticed that the time via NTP is incorrect, resulting in incorrect start and end times for all available SSID's. I've set the timezone to Amsterdam, but I can't find where I can change the NTP settings. As you can see in the screenshot, NTP registers a log entry at 5:00 AM saying it's 4:00 AM. That is…
-
Fail NWA220AX-6E Access Poin
I bougth an access point on March 2023 by Amazon but in last days this device become wrong function. In this moment is down in nebula and i try to access this by local network but is not possible. How can i get the gruarantee for this device. I have other 3 devices but this is the only AP whit problems
-
USG Flex 700 AP Management "Update Available"
Nothing I do seems to trigger the AP's to update, multiple "WAX630s". "Device can't connect to server" is showed under "Firmware". What is the trick to getting the AP to update firmware from the USG? Router> nslookup zapimg.cloud.zyxel.com Trying "zapimg.cloud.zyxel.com"…
-
NXC2500 Dashboard can't accesss
Hello Everyone, i need you advise here, i can not access NXC2500 dashbord from other subnet, however, when i use Wifi connection the dashboard can be access it, it try to disable the firewall on NXC2500, unfortunately the problem still persist. i try to find out in internet but no luck. also i can ping the IP when i use…
-
How to properly remove NWA50AX from Nebula NCC
I installed the AP using the NCC Nebula method. After noticing, that Nebula is not free of charge, I removed the Device in my Nebula APP, reset the device and re-configured it locally using the Configuration Wizard within the Web Browser. However, when the AP reboots, the Dashboard still shows the AP as registered in the…
