-
NWA50AX no mobile voice calls
As per title. Motorola G9 play indicates it is configured for wifi calls, but none work. Data works fine, text and webpages etc. Router is a Draytek 160 configured as a router, connected to the DSL phone line. Swapping the above for a Zyxel 1312B gives voice calls on the mobile. AP is as above, no subscriptions taken.…
-
Disconnect after DCS
I have several NWA 50 ax and they have been working fine for a long time. But recently some of my WiFi devices have dropped connection after DCS set to 3 in the morning. See below To get them connected again I need to restart them. what could have happened. Nebula mesh network what as well mean the red lines below the…
-
Uplink Interface goes down when Configuring WDS Link between two NWA130BE APs
Hello First post, so here goes. I have recently purchased 2 NWA130BE APs and I am attempting to configure them standalone in this simple topology: Internet —> gateway —> XMG105HP —> AP —> WLAN —> AP (+PoE injector) The APs are now running firmware 7.20 but out of box they were running an earlier version - sorry, I don't…
-
good practice for setting up a wifi AP to access LAN ressource
hi in office, we only use wired LAN we have Wifi AP only for guests and employee's personnal devices. thi Wifi is on a specific ISP modem and no link with office's lan i want to add a wifi AP for coworker when they are many in meeting room, because add a switch on the meeting desk is messy and laptop has no rj45 connection…
-
Wireless AP 7.30 firmware release notes
Hello, Todays release of 7.30 for BE access point doesn't seem to have a corresponding release notes, are there any plans to share what has been fixed and what new bugs have been found?
-
WAX640S-6E: which standard PoE is needed?
Hello everyone, following this post: https://community.zyxel.com/en/discussion/20800/zyxel-aps-and-compatible-poe-standards I used a PoE+ switch (non Zyxel) to have this AP online: But Nebula is telling me that it needs PoE++: How can I solve that?
-
Device falling off 2.4GHz radio since upgrade to 7.20 for NWA130BE.
I noticed that a particular device has been falling off the 2.4GHz since the upgrade from 7.10 to 7.20 for a NWA130BE. I only noticed it because the device is actually rebooting a few times a day since that upgrade. No other devices are having this problem even if they are much further from the AP. Although I am not…
-
NWA130BE troubles
Dear, I have the following set-up: Zyxel Nebula FWA 710 5G outdoor router, connected (PoE) to Zyxel GS1005HP 5-port PoE switch zyxel NebulaFlex NWA130BE wifi access point (connected to the switch with PoE) My problem is that I have no internet when connecting wireless with the NWA130BE (both phone and computers). the…
-
NWA90AX-PRO: Cannot access local management configuration wizard
I have a NWA90AX-PRO AP and I do NOT want to set up a Nebula account just to configure the thing. I only have 1 AP and have absolutely no need or desire to "centrally" configure it. That would make sense if I was a business managing multiple APs across many locations, but for a simple, single home AP, there's absolutely no…
-
NWA50BE PRO Problem with 6GHz
If I change the bandwidth from 320 to 160, I lose the 6 GHz net?
-
How to add NWA50BE PRO to USG FLEX 200 Wireless configuration
Anyone able to guide? NWA50BE PRO operational, in same (subnet) network, in Nebula. However want to add this AP into USG FLEX 200 Wireless configuration settings. (Do not want access details all over Nebula). 1 Internet search informs me that is should be possible, but unable to do so following that info. 2 Configuration -…
-
WBE660S is launching but is not booting (not getting IP address)
Hi All, I have the issue with WBE660S: it is not booting (no IP assigned) led is green uplink leds are keeping lighting (orange and green) reset button is not working (device is not restarting) doesnt matter if power is over USBC or POE via POE++ switch device. power consumption on the switch side is showing just around 6W
-
We have WAX630S, can we get a Wi_Fi repeater to those Access point
We have WAX630S, can we get a some kind of Wi_Fi repeater to those Access point?
-
NWA210BE doesn't have a QR code for Nebula.
When I'm trying to add it manually to my Nebula device list, it says that the device is registered to another account. How can I reset it?
-
Cannot perform firmware upgrade on NWA50AX Pro
I tried to upgrade the firmware of my NWA50AX Pro form "V6.55(0) / 2023-03-23 00:26:26" to the latest 7.10(ABYW.3)C0. But when uploading the firmware (.bin file) in the webUI it fails: I tried different Browsers, all with the same error. Is the firmware actually corrupted?
-
Connection issues with NWA130BE and Pixel 9 Pro
Since the upgrade to the latest firmware version V7.20(3) on my NWA130BE the Wifi does not work properly anymore on my Google Pixel 9 Pro. The Pixel is connected to the Access Point, but the internet is not reachable. When I start to Ping a host, the first couple pings might working, but the rest usually fails and I'm…
-
NWA210AX: current firmware fails after 49 days 17 hours uptime
Okay, this is pretty out of left field, but can anyone else confirm it? I have two of these units, both running V6.50(2) firmware. Several weeks ago one of them suddenly went nuts, dropping lots of packets and failing to respond to most pings. I tried to log into its web GUI and it was unbelievably slow to respond.…
-
Random WiFi connection issues with Apple devices
Hello everyone, sometimes I have some random issues mainly with Facebook/TikTok social videos playing: it happens that the customers tell me that they see the WiFi logo with medium/full power but also the spinning wheel. When they try to check the WiFi connection they see that also other apps on that device are not loading…
-
Bought two Zyxel APs from Amazon and they're "locked by device owner".
@Zyxel_CSO as per the title. I can't directly raise a support ticket because I do not have a subscription.
-
zyxel NWD7605 wifi adapter linux driver troubles on linux mint 22
I recently installed linux mint on my pc and my zyxel wifi adapter is not working. I'm new to linux so i'm completely lost at what to do, i somewhat modified the install.sh file that came with the driver to actually make it executable in terminal in the folder with the following command: "sudo chmod +x install.sh". I then…
