-
AP NWA50AX
I have installed AP NWA50AX on my network. I see SSID Ap on all devices except Notebook Hp Pavilion dv6 6170. I have also installed an USB wifi card but I didn't solve the problem
-
ZWO entry for NWA55AXE
NWA55AXE unfortunately doesn't appear as an AP in the ZWO planner software (v1.0.7) What's the best alternative AP to use that's a representative of that heatmap? Also any other suggestions for wifi planning with Zyxel especially with mesh in mind? Thanks
-
NWA1123-ACv2 blinking leds Green and Orange
Hi, my device is continuing having the green led and orange light led blinking. It's mounted in my roof so not easily accessible; it is powered with PoE ethernet cable, I've tried several time to unplug/replug the cable from the router but unsuccessfully. It is not reachable through its IT address assigned by the router…
-
NWA210AX can't setup...
Got this router used at a sale but it doesn't seem to work. It turns on and I reset it using the hardware switch on the back but it is now not working. The light blinks yellow and green. WiFi shows Zyxel 01f1 but any attempt toget to the admin page doesn't work. Also doesn't work via network cable in either port.
-
Pole and wall mount for NWA55AXE?
According to QSG available on zyxel website, there's optional wallmount and polemount for NWA55AXE. However, among accessories, i find only ACCESSORY-ZZ0102F (Weatherproof Enclosure Kit, which should not be needed for this device) and ACCESSORY-ZZ0106F (pole mounting kit) which seems dedicated to ACCESSORY-ZZ0102F… I'm…
-
Older 802.11ac client has low throughput (NWA130BE)
I have the following rather simple setup: Home router with integrated Gigabit switch (FritzBox 6590 Cable) Ceiling mounted NWA130BE connected via Cat.7 to the router/switch 2.4GHz, 5GHz and 6GHz radios all enabled There are only one or two neighbouring APs on the same 5GHz channel I have an older wireless client (Sony…
-
NWA1123ACv3 not responding to hard reset.
Hello Support, I unplugged my wireless router for general maintenance and when I plugged it back in again it won't start. The LED is continuously solid green and the ethernet port is completely inactive. I've tried resetting the device several times using the reset button from 5 to 60 seconds but the device is still…
-
NWA50AX no mobile voice calls
As per title. Motorola G9 play indicates it is configured for wifi calls, but none work. Data works fine, text and webpages etc. Router is a Draytek 160 configured as a router, connected to the DSL phone line. Swapping the above for a Zyxel 1312B gives voice calls on the mobile. AP is as above, no subscriptions taken.…
-
Disconnect after DCS
I have several NWA 50 ax and they have been working fine for a long time. But recently some of my WiFi devices have dropped connection after DCS set to 3 in the morning. See below To get them connected again I need to restart them. what could have happened. Nebula mesh network what as well mean the red lines below the…
-
Uplink Interface goes down when Configuring WDS Link between two NWA130BE APs
Hello First post, so here goes. I have recently purchased 2 NWA130BE APs and I am attempting to configure them standalone in this simple topology: Internet —> gateway —> XMG105HP —> AP —> WLAN —> AP (+PoE injector) The APs are now running firmware 7.20 but out of box they were running an earlier version - sorry, I don't…
-
good practice for setting up a wifi AP to access LAN ressource
hi in office, we only use wired LAN we have Wifi AP only for guests and employee's personnal devices. thi Wifi is on a specific ISP modem and no link with office's lan i want to add a wifi AP for coworker when they are many in meeting room, because add a switch on the meeting desk is messy and laptop has no rj45 connection…
-
Wireless AP 7.30 firmware release notes
Hello, Todays release of 7.30 for BE access point doesn't seem to have a corresponding release notes, are there any plans to share what has been fixed and what new bugs have been found?
-
WAX640S-6E: which standard PoE is needed?
Hello everyone, following this post: I used a PoE+ switch (non Zyxel) to have this AP online: But Nebula is telling me that it needs PoE++: How can I solve that?
-
NWA130BE troubles
Dear, I have the following set-up: Zyxel Nebula FWA 710 5G outdoor router, connected (PoE) to Zyxel GS1005HP 5-port PoE switch zyxel NebulaFlex NWA130BE wifi access point (connected to the switch with PoE) My problem is that I have no internet when connecting wireless with the NWA130BE (both phone and computers). the…
-
NWA90AX-PRO: Cannot access local management configuration wizard
I have a NWA90AX-PRO AP and I do NOT want to set up a Nebula account just to configure the thing. I only have 1 AP and have absolutely no need or desire to "centrally" configure it. That would make sense if I was a business managing multiple APs across many locations, but for a simple, single home AP, there's absolutely no…
-
NWA50BE PRO Problem with 6GHz
If I change the bandwidth from 320 to 160, I lose the 6 GHz net?
-
How to add NWA50BE PRO to USG FLEX 200 Wireless configuration
Anyone able to guide? NWA50BE PRO operational, in same (subnet) network, in Nebula. However want to add this AP into USG FLEX 200 Wireless configuration settings. (Do not want access details all over Nebula). 1 Internet search informs me that is should be possible, but unable to do so following that info. 2 Configuration -…
-
WBE660S is launching but is not booting (not getting IP address)
Hi All, I have the issue with WBE660S: it is not booting (no IP assigned) led is green uplink leds are keeping lighting (orange and green) reset button is not working (device is not restarting) doesnt matter if power is over USBC or POE via POE++ switch device. power consumption on the switch side is showing just around 6W
-
We have WAX630S, can we get a Wi_Fi repeater to those Access point
We have WAX630S, can we get a some kind of Wi_Fi repeater to those Access point?
-
NWA210BE doesn't have a QR code for Nebula.
When I'm trying to add it manually to my Nebula device list, it says that the device is registered to another account. How can I reset it?
