-
NWA50ax Pro - Decrease transmission power at night
Hi! I just bought an NWA50ax Pro AP and started to set it up (in Standalone Mode). I would like to lower the transmission power of the 2.4G radio and turn off the 5G Radio at night. The AP is operating in a private hause and it's not necessary to have full power over night. How can I achieve this? Thanks.
-
Controller AP Group Function
What function to do the AP groups serve on the Flex H AP controllers? Is roaming limited to APs within a group? I have several APs in a building and one of them serves an older b/g IOT device. I'd like to put this one in a separate group with the older functionality enabled (control rate <11 Mbps, and ax/ac/n station only…
-
[NWA130BE] - MIB Files for SNMP Protocol
Hello everyone, I see that is possible to enable the SNMP Protocol for the AP in object. Can I have access to the MIB Files for the private SNMP OID? Thank you
-
how do I setup different schedules on different SSID's from the same AP
-
WLAN unstable and kernal panic after Update clients to IOS/MacOS26
Hi, i use a WBE660s on latest firmware. After Patch 7.20P2 the AP runs without any problems for a while. After updating to IOS 26 and MacOS 26 the AP becomes unstable. Every aprox 24h the 26-Clients could not connect to wlan anymore. After disabling and enabling SSID in Nebula-App it works fine. Last night i see 2 reboots…
-
Router 5G NR-5103Ev2 and Multy M1
It is possible to connect this router with the Multy M1 to create a mesh network? Thank you
-
Wireless bridge functionality
Hello everyone, I need some wireless bridges to link different LAN segments. I need to use that option both on Nebula and on prem. I see that here on Nebula: You can see that option on Nebula: but it is not always available: I found this list:…
-
Zyxel NWA50AX PRO - Solid green LED - Not responding - No IP - No Wifi
Good evening everyone, I'm having trouble with my Zyxel NWA50AX PRO—the device just stopped working overnight. Even though it gets warm when powered up (same temperature range as my other two units), and the status LED stays solid green (which should mean it's connected to clients, but in this case, it never switches…
-
ZyXEL P-2000W_V2
What battery is compatible with the ZyXEL P-2000W_V2? Where can I buy a genuine battery?
-
NWA1123-AC HD in boot loop. Hardware or software problem ?
Hello, I've a NWA1123-AC HD Access Point. It runs firmware 6.25. When I got it, it was already not working : no Wifi network, no Web GUI access, no IP address assigned by my DHCP server. I connected to it via console port and saw that it was stuck in a boot loop. I succeeded at flashing the last firmware available but the…
-
WDS SSID is NOT hidden
Hello, I managed to connect two AP’s via WDS. But…. now I see an additional WiFi. I though the created profile will be used to connect the AP’s, so that they can “communicate” with each other. So, here are my questions: I see now a new WiFi access point (SSID) available called “MyZyXELWDS”. I thought this will be used the…
-
Help with NWA50BE Pro
I want to set this up to use only 5GHz on radio 1 and 6GHz on radio 2. I have been advised that this is possible. I have disabled(unchecked) the 2.4 GHz band. Leaving 5Ghz and 6Ghz selected on both radios and setting radio 2 to 6Ghz. If I then look at the dashboard (standalone), the 2.4Ghz is still visible on radio 1, and…
-
I now have 2 NWA130BE APs and 1 NWA50AX-Pro
I have a some 2.4ghz devices now always disconnecting. Both my Chamberlain Garage door openers and my Abode Security cameras. I have tried every setting possible to make it better but nothing is working. Here is a snippet from the event log:
-
[FWA 510] - Unable to use WiFi AP when Cellular IP forwarding is on
I've been struggling with this. I set up a new router to be the main router for my home wifi, while using the Zyxel FWA 510 as the 5G internet modem and as wifi AP. When I switch on Cellular IP forwarding, to forward the internet traffic from my Zyxel router to the new router, the wifi on the Zyxel stays on, but I cannot…
-
NWA50BE 5G Channel Width limited at 160 Mhz
I purchased the NWA50BE (BE5100) access point. Based on its 5sG network specifications, it should support bandwidth up to 240 MHz, but in the standalone configuration, I see that it's limited to 160 MHz. How do I set 240 MHz? Thanks
-
problem
i HAVE BUY wbe660 ap AND NWAX110 REPEATER AND I WANT CONNECT PC ON NETWORK CARD NWAX110, BUT CANT WORK
-
NWA90AX Pro Dynamic VLAN Assignment via Radius
I have an NWA90AX Pro configured as a stand-alone AP. The management VLAN is tagged and set to 1. The Security profile for the SSID is set to WPA3 Enterprise and Radius. The SSID is set to VLAN 20. When a client authenticates, I can see the Radius server sending VLAN 30, but the AP does not set the client on VLAN 30,…
-
Roamin issue - nwa220 and WBE530d
Hi, I have at network of 13 AP´s mainly NWA220 and WBE530d. I have the issue that some clients does not want to let go of the 530´s but stay connected even though there is a 220 very close by. I have enabled smart steering and modified the threshold, no luck. 802.11k/v is also enabled. All is on the same SSID of course,…
-
Connect IoT without WPS
Hello everyone, this is my first time configuring and managing Zyxel products with Nebula. I hope you can help me. I need to connect an IoT device to my AP, but according to the documentation, I need to enable WPS on my AP, which is not possible with Zyxel APs. How can I connect my IoT device directly to the network? Thank…
-
I need firmware for NWA5123-NI
Could anyone please help me locate the firmware version 5.10(AAHY.10) for the NWA5123-NI access point?
