Setup options\dhcp\webpage\
Options
General_Musa
Posts: 1 Freshman Member
Hi,
Just got multyX in house. I have a fairly complex setup with a vairity of stuff from door controllers to alarm-systems. This is configured with static ip on an router with i use in connection to work through vpn.
THIS means that i cannot without doing serious reconfiguration use another ip-range.
question:
CAN you disable dhcp?
HOW the he** do i access the web-based configuration page(error 404)
Can both units be used with cable from the sentral router(if so, do i use WAN in both?)
Can the system be set with static ip and as pure accesspoints?
Is there any way of going deeper into wireless-settings, and setting up several networks(i obviously need an pure 2.4 ghz network for the wireless function on the robot-vacuum)
Thanks for input!
#MultyX_January
Just got multyX in house. I have a fairly complex setup with a vairity of stuff from door controllers to alarm-systems. This is configured with static ip on an router with i use in connection to work through vpn.
THIS means that i cannot without doing serious reconfiguration use another ip-range.
question:
CAN you disable dhcp?
HOW the he** do i access the web-based configuration page(error 404)
Can both units be used with cable from the sentral router(if so, do i use WAN in both?)
Can the system be set with static ip and as pure accesspoints?
Is there any way of going deeper into wireless-settings, and setting up several networks(i obviously need an pure 2.4 ghz network for the wireless function on the robot-vacuum)
Thanks for input!
#MultyX_January
0
All Replies
-
Welcome to ZYXEL COMMUNITY HOME FORUM! Please see my answer as below.- CAN you disable dhcp?You can use Bridge Mode. (To install your Multy X as Wireless Access Point in your house.)Please refer to https://homeforum.zyxel.com/discussion/621/bridge#latest- HOW the he** do i access the web-based configuration page(error 404)Multy X does not support web-based configuration page.Please refer to https://homeforum.zyxel.com/discussion/comment/1348#Comment_1348- Can both units be used with cable from the sentral router(if so, do i use WAN in both?)Multy X has not yet supported Ethernet backhaul.Please refer to https://homeforum.zyxel.com/discussion/comment/1160#Comment_1160- Can the system be set with static ip and as pure accesspoints?When Multy X is Bridge Mode, you can set the static IP for it from upper layer router.- Is there any way of going deeper into wireless-settings, and setting up several networks(i obviously need an pure 2.4 ghz network for the wireless function on the robot-vacuum)You can disable Single WiFi Name. It will separate SSID of 2.4GHz & 5GHz .Please refer to https://homeforum.zyxel.com/discussion/comment/1318#Comment_13180
Categories
- All Categories
- 383 Beta Program
- 2.1K Nebula
- 117 Nebula Ideas
- 80 Nebula Status and Incidents
- 5.1K Security
- 76 USG FLEX H Series
- 247 Security Ideas
- 1.3K Switch
- 69 Switch Ideas
- 907 WirelessLAN
- 34 WLAN Ideas
- 5.9K Consumer Product
- 209 Service & License
- 335 News and Release
- 71 Security Advisories
- 21 Education Center
- 5 [Campaign] Zyxel Network Detective
- 1.9K FAQ
- 894 Nebula FAQ
- 415 Security FAQ
- 233 Switch FAQ
- 205 WirelessLAN FAQ
- 46 Consumer Product FAQ
- 137 Service & License FAQ
- 34 Documents
- 34 Nebula Monthly Express
- 73 About Community
- 62 Security Highlight