Can't install SMB V2 on NSA325v2

derboum
derboum Posts: 5
First Comment
in Personal Cloud Storage
Screenshot 2023-05-19 222810.png

Hello everyone,

i tried to update samba on my Zyxel NSA325v2 according to this HOW TO https://zyxel.diskstation.eu/forum/viewtopic.php?t=24&sid=3e40a8ef0b230af1ad6c9d0802170f46

It fails at the Point where i start /opt/etc/init.d/S09ZyXELSambaReplacement.

An error accured: mw: can`t rename '/opt/var/lock/*': No such file or directory

Can anyone help me?

Best Regards

All Replies

  • Mijzelf
    Mijzelf Posts: 2,816  Guru Member
    250 Answers 2500 Comments Friend Collector Seventh Anniversary

    That is caused by next lines in the start script:

        # Move /opt/var/lock to ramdrive, else the maintenance of browse.dat will keep the disk awake
    
    if [ ! -h /opt/var/lock ] 
    
    then
    
        mv /opt/var/lock/* /var/lock/
    
        rmdir /opt/var/lock && ln -s /var/lock /opt/var/lock
    
    fi

    Apparently you don't have an /opt/var/lock directory, so you can just create the symlink

    ln -s /var/lock /opt/var/lock

  • derboum
    derboum Posts: 5
    First Comment

    Thank you for the quick answer.

    Unfortunetly after i did the command 

    ln -s /var/lock /opt/var/lock

    and then tried to start

    /opt/etc/init.d/S09ZyXELSambaReplacement start

    nothing happens.

    What can i do?

  • Mijzelf
    Mijzelf Posts: 2,816  Guru Member
    250 Answers 2500 Comments Friend Collector Seventh Anniversary

    Try restart instead of start. Or reboot the box.

  • derboum
    derboum Posts: 5
    First Comment

    Tried both. Nothing happens.

    Anything else i can do?

  • Mijzelf
    Mijzelf Posts: 2,816  Guru Member
    250 Answers 2500 Comments Friend Collector Seventh Anniversary

    Use the 'debug mode' of the startscript:

    /bin/sh -x /opt/etc/init.d/S09ZyXELSambaReplacement start

  • derboum
    derboum Posts: 5
    First Comment
    edited May 2023
    grafik.png

    Is this good or bad?

    I tried to check smbstatus but it throws an error.

  • derboum
    derboum Posts: 5
    First Comment

    ~ # /bin/sh -x /opt/etc/init.d/S09ZyXELSambaReplacement start

    • prgmname1=/opt/sbin/nmbd
    • prgmname2=/opt/sbin/smbd
    • configfile=/opt/etc/samba/ZyXELSambaReplacement.conf
    • nmbdpid=/opt/var/run/nmbd-ZyXELSambaReplacement.conf.pid
    • smbdpid=/opt/var/run/smbd-ZyXELSambaReplacement.conf.pid
    • basename /opt/etc/init.d/S09ZyXELSambaReplacement
    • [ S09ZyXELSambaReplacement = samba.sh ]
    • startreplacement
    • [ -f /etc/init.d/samba.replaced.sh ]
    • return
    • exit

    this is the output.

  • Mijzelf
    Mijzelf Posts: 2,816  Guru Member
    250 Answers 2500 Comments Friend Collector Seventh Anniversary

    [ -f /etc/init.d/samba.replaced.sh ]

    return

    Are you sure that it isn't automatically started on boot? The start procedure is roughly

    • Stop stock firmware (/etc/init.d/samba.sh stop)
    • Rename firmware startscript to /etc/init.d/samba.replaced.sh
    • Create a symlink /etc/init.d/samba.sh to /opt/etc/init.d/S09ZyXELSambaReplacement
    • Start the Entware samba via this symlink (/etc/init.d/samba.sh start)

    The symlink is created because the firmware uses it to restart samba when needed. This way the firmware restarts the Entware samba without knowing (or needing to know)

    Stopping of the replacement is the same sequence reversed.

    The script checks if the renamed startscript is available, and if so, then exits, which seems to be the case.

Categories

Consumer Product Help Center

EnglishTiếng ViệtРусскийไทย中文（台灣）