NWA1123-AC-HD

Damien_SBM
Damien_SBM Posts: 7
First Comment Friend Collector First Anniversary
in Security

Hi everybody,

I would know if it's possible to have Two SSID with different range address ip ?
Or it's exclusive to Nebula ?

Thanks

Accepted Solution

  • Zyxel_Kay
    Zyxel_Kay Posts: 1,280  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - WLAN Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security
    Answer ✓

    Hi @Damien

    Yes, it is possible to have two SSIDs with different IP address ranges. As PeterUK mentioned, you can achieve this by setting up VLANs on your Zyxel Access Point (AP) and configuring your USG FLEX firewall to handle the different IP address ranges for each VLAN.

    Here's a brief overview of the steps:

    1. Configure VLANs on the USG FLEX:
      • Log in to your USG FLEX web interface.
      • Navigate to Configuration > Network > Interface > VLAN.
      • Create VLANs for each SSID with the desired IP address range.
    2. Set up SSIDs on the Access Point:
      • Log in to your Zyxel Access Point's web interface.
      • Go to Configuration > Wireless > SSID.
      • Create or edit the SSIDs and assign them to the corresponding VLANs.
    3. Assign VLANs to SSIDs:
      • In the same SSID configuration section, ensure each SSID is tagged with the correct VLAN ID.
    4. VLAN Traffic Through Switches:
      • Ensure VLAN traffic is allowed if there is any switch between your AP and firewall.

    For more details about creating SSIDs in standalone mode, you may refer to this article:

    https://community.zyxel.com/en/discussion/13899/how-to-create-an-ssid-on-standalone-mode

    Kay

All Replies

  • PeterUK
    PeterUK Posts: 3,539  Guru Member
    100 Answers 2500 Comments Friend Collector Seventh Anniversary

    You need a USG doing VLANs to do this

  • Damien_SBM
    Damien_SBM Posts: 7
    First Comment Friend Collector First Anniversary

    an USG FLEX 500 can make it ?

  • PeterUK
    PeterUK Posts: 3,539  Guru Member
    100 Answers 2500 Comments Friend Collector Seventh Anniversary
    edited July 2024

    Yes then with the AP and PoE+ to USG and AP config the given VLAN IP subnet on that base port with a zone with SSID AP setting to the given VLAN ID

  • Zyxel_Kay
    Zyxel_Kay Posts: 1,280  Zyxel Employee
    Zyxel Certified Network Engineer Level 2 - Nebula Zyxel Certified Network Engineer Level 2 - WLAN Zyxel Certified Network Engineer Level 2 - Switch Zyxel Certified Network Engineer Level 2 - Security
    Answer ✓

    Hi @Damien

    Yes, it is possible to have two SSIDs with different IP address ranges. As PeterUK mentioned, you can achieve this by setting up VLANs on your Zyxel Access Point (AP) and configuring your USG FLEX firewall to handle the different IP address ranges for each VLAN.

    Here's a brief overview of the steps:

    1. Configure VLANs on the USG FLEX:
      • Log in to your USG FLEX web interface.
      • Navigate to Configuration > Network > Interface > VLAN.
      • Create VLANs for each SSID with the desired IP address range.
    2. Set up SSIDs on the Access Point:
      • Log in to your Zyxel Access Point's web interface.
      • Go to Configuration > Wireless > SSID.
      • Create or edit the SSIDs and assign them to the corresponding VLANs.
    3. Assign VLANs to SSIDs:
      • In the same SSID configuration section, ensure each SSID is tagged with the correct VLAN ID.
    4. VLAN Traffic Through Switches:
      • Ensure VLAN traffic is allowed if there is any switch between your AP and firewall.

    For more details about creating SSIDs in standalone mode, you may refer to this article:

    https://community.zyxel.com/en/discussion/13899/how-to-create-an-ssid-on-standalone-mode

    Kay

  • Damien_SBM
    Damien_SBM Posts: 7
    First Comment Friend Collector First Anniversary

    Thanks a lot !

Categories

Security Help Center

EnglishTiếng ViệtРусскийไทย中文（台灣）