-
NR5101 to much speed connection lost…
hey everyone, like you can see in the screenshots, my connection goes from 250mbps to this… in a night, and I didn’t touch anything in the morning I tried to watch an video on YouTube like usual it’s goes to 2K/4K by it own but it was like 480p when I tried the speed it was 10mbps… I will take and appreciate any helps from…
-
My WX3100-T0 Power Led keeps flashing fast forever and the unit does not startup
I bought 2 units WX3100-T0 to use as AP's. The 1st one was configured by me (fixed IP address, other SSID/pswd, firmware update) and is working fine. The same steps done for the 2nd one, but after power-on the Power Led keeps flashing very fast forever and the unit does continue not startup. It responds to ping, but is not…
-
Zyxel NBG6817 U-boot Recovery
I have a couple of APs that were flushed with a custom openwrt build for FB-Soma-mesh Project that I would like to recover and flash with a newer openwrt/zyxel firmware... I currently do not have root password but I do have serial access... The failsafe mode has been disable and also tftp boot prompt by pressing the wps…
-
replacement for ZYXEL router version XMG3927-B50A
Hi, I live in the UK and at the moment I`m on a FTTC with TalkTalk. Im using a ZYXEL version XMG3927-B50A as my gateway modem/router this is connected to two (2) TP-Link Archer AX50 routers via cat cable these routers are all linked/setup in In access point (AP) mode. Everything is working great, no problem all I want to…
-
DX3301 putting in to Modem Mode
Hi All, Sorry you may need to go a little as as I am not that tech savvy I want to put my router in to Modem mode but what I have tried does not seem to work. I am trying to connect a set of Tenda Nova as the WIFI I have is very bad, I was looking to see if the set of 3 Mesh Tenda Nova will help. Can you advise what wire…
-
DX5401-B0 - Downlaod latest stockfirmware and source code
Hi. Where can I download DX5401 latest stock firmware? How can ask to receive source code for DX5401-B0? I asked it via email (firmware and source code) but no answer. Thanks. KR.
-
EMG3525-T50B: single laptop can not connect to wifi
HelloRouter: EMG3525-T50B firmware V5.50(ABPM.2)H0Problem Laptop: ASUS, windows 10 x64 19042.1110 with Intel Dual Band Wireless AC 7265When I connect to the zyxel router with wifi, it says "cant connect to this network"I can connect to it with a LAN cable The wifi network on the device is working fine except for one…
-
Zyxel EX3300-T0 - Issues connecting WhatsApp / Facebook / Speedtest / Smart TVs
Hi, we recently installed Zyxel EX3300-T0 routers at one of our campsites which have P2P links back to a main basestation. If you plug directly into the P2P you don't encounter any issues like this but as soon as you are on the WIFI of the router we have the following issues: Smart TVs (mainly samsung) will not connect to…
-
DX5401 ATEN/ATSE
Hi all! I'm trying to make some changes to the bootloader of the DX5401-B0, but I cannot set the debug flag to 1. When I type ATSE DX5401_B0, it gives me this code: 2501000E090013009C030490330691452269 Which code can I use to run ATEN 1 command and enable debug mode? Thank you for your help!
-
zyxel emg3525-t50b - can't open port 22 for SSH
I want to open ports 22 (TCP) for SSH (incoming traffic) on my MX Linux (21.3) server. I installed the firewall and the port is open according to the operating system. In addition to that I changed the following on the Router (192.168.1.1) after I logged in - Go to: Network Settings, NAT, Port forwarding (landing page).…
-
ZYXEL DX3200-B0 Turk Telecom
Hello, I have a ZyXEL DX-3200 B0 router that my internet service provider provided. There are blind spots in my house where wi-fi signals can't reach. I want to buy an access point with mesh system that is suitable for the modem I have. What do you recommend?
-
Broadband menu on EX3301-T0
I am trying to set up external access for a server plugged into the broadband of the router. I believe to do this I need to set up upnp and several port fowarding. While reading the manual it says to access the broadband menu from network setting. For me, it is not there. how can I get it back? in the end I want ports to…
-
Repeater
What do you suggest of repeater for zyxel 5501? 2.4 GHz network thank you 👍
-
Zyxel DX5301-B2
Hi. I have a Zyxel DX5301-B2 router. Firstly, where can I get the latest firmware for this router? The Zyxel website doesn't even seem to acknowledge this router exists. Secondly, I have a concern with this router that the Web Configuration GUI is listening on both ports 80 and 443 on both the LAN and WAN interfaces. I do…
-
Changing WAN port to 5th LAN port?
How this is usually done? I have VMG3926-B10A, which says in User's Guide's page 180: "LAN5 displays if WAN port was configured as a LAN port in the Home Networking > 5th Ethernet port screen." Maybe this is a mistake or maybe this feature is removed from latest fw. But since the device is EoL…
-
zyxel nr5101 router blocking access to website / apps
Hi guys, My Zyxel nr5101 Router is blocking access to websites such as Twitter and Linkedin. I'm also unable to open Whatsapp, Slack or Discord apps on both my computer and phone. This is the case for everyone using our WiFi. Initially I used a VPN to fix this but now I can't even connect to my VPN anymore. I'm with EE for…
-
NBG7510 - how can I add a static route? The Routing sub-menu is missing in ABZY.3
Hello, I am setting up my NBG7510 and have updated it to V1.00(ABZY.3)C0 ok. I am using my Zyxel DSL home gateway to get to the Internet successfully, so I have not configured any Broadband settings in the NBG7510. The WAN port is connected to a LAN port on my Zyxel DSL home gateway and has come up as shown below. However,…
-
Compatible extender for Zyxel C4000bz?
My wifey's MacBook Pro keeps dropping its wireless connecton where she sits 90% of the time she surfs. We noticed the Mac reconnects when she goes to another room. Our modem is in a wiring closet behind our 82" Samsung flat which I believe attenuates the modem signal in the direction she sits. Ask: Can someone recommend a…
-
ZYXEL EX5601-T0 - how to assign the same NAT forwarding ports to 2 lan IPs?
Hello everyone! I have a ZYXEL EX5601-T0 https://service-provider.zyxel.com/global/en/products/ethernet-cpe/ethernet-iads/ex5601ex5600-t-series I can't solve this issue: PC 1: assigned static ip 192.168.1.100 PC 2: assigned static ip 192.168.1.200 In NAT section I opened , for PC 1, ports 50100 and 50101 for TCP/UDP…
-
Can't login to my router web
Hello, I can't login to my Zyxel router web interface I have input the default user name and password but still. All I am getting is wrong username/password.
