-
When radar signal detected and channel changes, I lose the mesh network
I have 3 NWA50AX, one connected by ethernet the others connected as a wifi mesh. I have noticed that my mesh goes down when a radar signal has been detected and the 2 NWA50AX connected via wifi are no longer connected, and are flashing green and yellow. They do not seem to recover and the only solution I have is to power…
-
My RADIUS Auth via local network does not work
Hi, i've set up a RADIUS Sever for a SSID and added the LAN IP in Nebula. But if i am offline the authentication does not work, because the external IP is used: AP Log: 2022-11-28 15:33:05 10.10.100.35 0" dst="0.0.0.0:0" msg="User baba (MAC: a2:5d:32:xx:xx:xx) 802.1X auth timeout. (Server: 91.42.xxx.xxx:1812, Timeout:…
-
Zyxel NWA90AX, Offline in Nebula Cloud
I have a concern regarding to our NWA90AX, it is already connected to the Nebula Cloud, and it says Offline in Access Point Status Monitoring even though we can connect to its Wi-Fi with Internet Connection. Also, No LAN IP & Gateway in the Access Point Status. Thanks in advance for the help and tips. Best Regards, Mark
-
Nebula tunnel gets rebuilt every 30 seconds
I have a strange situation, there is a site-2-site VPN between two sites, (One Nebula NSG100 and a USGFLEX100W) and apparently the tunnel gets rebuilt every 30 seconds for some reason, ping gets through without any loss, but I can't find the reason, also there is not much in the logs that would help. Can anyone help me…
-
802.1x Cloud Auth Security
I have not seen any updates to the KB article demonstrating device authentication via WPA2/3 Enterprise with LEAP as phase 1 and NONE as phase 2. This is insecure and goes against current best practice. Has there been an update to this config method? If so can someone please direct me to it? If not Zyxel should update…
-
NWA50AX firmware V6.29(ABYW.0)
Hi, Today I did a software updateV6.29 (ABYW.0), on the NWA50AX, and the device keeps rebooting. WiFi networks start, however after a few minutes, the AP restarts by itself, the ETH port flaps several times. Do you have any solution? The device cannot be used.
-
Blocking torrents
Here in the USA, the ISP's will often send notices if they detect that movies are being downloaded (typically via torrents) and threaten to terminate service. Currently I'm using both content filtering and Application Patrol to block P2P and Torrent sites. For Content Filtering: P2P Sites, and Usenet Sites. For Application…
-
default admin password brand new switch GS-1920-48HPv2 right out of the box.
The default admin password of admin and 1234 doesn't work with a brand new switch out of the box? was it changed?
-
Samsung TV KS8000 cannot connect to NWA210AX while connects fine to NWA90AX
I have three Zyxel NWA devices, one NWA210AX and two NWA90AX, handled by Nebula basic. One of my client devices, Samsung KS8000 (TV) cannot connect to NWA210AX. In Nebula client seems authenticated but without IP. If I turn off NWA210AX for a while, Samsung KS8000 connects to the upper room NWA90AX and gets IP just fine.…
-
NWA50AX connected to Zyxel Nebula offline if Internet connection is down?
Hello, i've 5 NWA50AX connected to nebula at a customer with bad internet connection (disconnects randomly). Every time the internet disconnects, the Access Points and the meshed WiFI is going offlline, even with static ip addresses. Is there a way to keep the wifi running, even if the internet connection is down? Why is a…
-
WiFi clients does not connect to the 5GHz band anymore
All WiFI clients connect only to the 2.4GHz band. All SSIDs are configured for 2.4GHz and 5GHz. Until recently, this worked normally and clients preferred to connect to the 5GHz band. I am exclusively running MWA110AX access points in the Nebula Cloud. "Band select" is activated. No settings were changed in Nebula, but…
-
L2TP VPN Active Directory authentication do not work
Hi everyone, I'm trying to set up an L2TP/IPSec VPN with AD authentication but it does not work because my user is rejected. The appliance is a USG Flex 100 managed by Nebula. First of all, I add my AD to Nebula And I configure the VPN server with my AD for authentication Then I add a test user to my AD users And finally,…
-
[NEBULA] Deauth by STA Timeout reason 2
Hello, some clients on my WLAN Network are randomly disconnecting themselves with the following message: Station: [MAC] has deauth by STA Timeout on Channel: 44, SSID: [SSID], 5GHz, Tx/Rx: 16160688/1367848 Bytes. reason 2, Interface:wlan-2-1 One of them has to restart the WLAN-Adapter to be able to reconnect again (Samsung…
-
NWA210AX lower transmit power on 5GHz compared to NWA90AX
I really don't understand why my NWA210AX shows transmit power of 16 dBm on lower 5GHz channels (36 to 64) when NWA90AX shows 23 dBm on the same channels on same place with same regulations applied and same channel width (80MHz). Can you explain the difference? When switching to channels of higher band (100 to 140),…
-
My clients, mostly IOT devices are being disconnected daily NWA50AX
I have 2 NWA50AX access points My clients, mostly IOT devices are being disconnected daily if I reboot the devices, everything reconnects. I've tried numerous things (unable to remember what, following advice on other threads etc) really spoiling my experience now, things like thermostats are bing disconnected and I'm…
-
Migration / Checklist NSG to USGflex // Nebula
Hi everybody, I am trying to find out the best pathway for a migration from an NSG100 to an USGFlex200 at one of our sites --- all nebula managed. From this forum I (seem to) know, that a real migration is not possible; rather a step by step re-installation. So please: what is the best way to migrates in a proven…
-
One unique device only for one voucher
Hello I like to know if is possible and if yes how to manage in Nebula Voucher that one code can be used only for one device it means if I use voucher code I can't login to WLAN with this code from any other device.
-
Nebula route-based VPN to Azure
Hi, is it possible to set up a route-based VPN to Azure from Nebula?I can get it to work with single subnets on each side, but not when there are multiple subnets.
-
zyxel NWA1123ACv3 standalone access fail
After connecting and registering, i accessed the router's page, via the ip that appeared in the nebula app. (192.168.1.20)The login screen opened, i entered the default user and password, admin/1234, but without success. I reset the equipment and even so it does not login with the default factory login.
-
No internet connection with NWA50AX
I have a new NWA50AX which is connected to internet but when connecting a PC or mobile phone to it, the result is "no internet connection". What should I do to have the internet connection working?
