-
Where to download USG100 legacy firmware
I have a remote office where the USG100 has failed. There is a USG100 kept as a spare but has never been upgraded. When I try to load the latest firmware onto the spare it is not compatible. I have read that I need to first install a later version of version 2.2.0 ( C6??) but the old firmware is no longer available for…
-
Connection with Internet provider
My internet provider gives me a ip address for as point to point connection with a mask 255.255.255.254, but even if i can insert in my ethernet port it seems it does not work I have a zywall 310
-
Public IP Whitelisting
How to whitelist Public IP address in ATP100?
-
L2TP over IPSEC parameters for Windows 10 native client
I have, on a USG Flex 200 (latest firmware version), a L2TP over Ipsec VPN policy. I've successfully tested with Android 9 and Android 11 native client. Parameters are: Phase1: IKEv1 - interface WAN1 - remote dynamic - preshared key - local id type: mail - remote id type: any - lifetime 86400 - mode aggressive -…
-
DHCP not working on vpn100
hi I have a remote site where using vpn100 and the remote site is connected to the main site via a VPN tunnel. tunnel works fine but the remote side vpn100 is not assigning auto IP to devices and I have to add manual IP then the clients work. I have updated the latest firmware also on the remote site VPN 100 is still DHCP…
-
Tommy
we have had 2 FLEX100 unit go completely down when power is removed. is there anything that can be done to avoid this on Our other units.
-
Site to Site USG110-USG700 Flex
Hi am am hoping to get some help with this setup, hope this is the correct place to ask questions, cant see anything wrong with the setup, ips checked preshared key checked devices rebooted etc, thanks in advance
-
How to Connect USG700 to USG310 With Lan cable
-
NAT and Security Policy Issue
We have configured 2 webservices(IIS & Apache) with different port and created service and define port range for the same than we configured NAT then follow with Security policy. Now one webservice (IIS) is not from public network and other webservice (Apache) is working fine with the same Security Policy. Both are…
-
Config migration atp200 to atp500
Hi everyone,i need to replace an atp200 with an atp500. Anyone knows if is possible migrate the configuration? Thanks in advance. Fred
-
Big traffic made through NAT freezes ZyWALL USG 200
Hi all! First of all I what to thank you all for this large community! It Helped me a lot these days to understand how Zywall USG 200 works. Here's my situation: internet cable is connected to WAN1 and I'm connecting to internet using a PPPOE connection. PPPOE external IP is named EXTERNAL_IP my local FTP server is called…
-
Join AD Domain in SD-WAN
Hello, I have a VPN100 firewall configured in SD-WAN. I have to join a local Domain Server since I have authentication problems to local services via VPN. I cannot find any guide to do it from SD-WAN Can anyone help me?
-
Cannot block youtube by appPatrol
Hello. I am using USG110, and have the license IDP. I set up AppPatrol to block Youtube, but the user can still access Youtube , just slower a bit. I don't know why? I upload my config below.
-
Really "Web Content Filter - Profile" of USG FLEX family has 256 elements limit?
In the company Firewalls where I replaced the old USGs with the USG FLEX family, I used an extremely restrictive configuration trusting in the possibility of opening sites in a granular way. I was therefore amazed to receive the message that the limit was reached on inserting the 257th element. Is this really the limit…
-
ASP.NET Applications behind USG Firewalls show USG local IP instead of web client public IP
what a subject! dear forum, We exchanged our old firewalls with a USG 110 and 210 firewalls. Since the exchange we get on ASP.NET web applications on IIS 7 or IIS 8.5 as client web address the IP address of the USG firewall. NAT is working fine: whenever I access the web from the IIS I get the specified public IP address…
-
WAN trunk spill over not working
Hello team, Please i want the correct & confirmed configuration for WAN trunk settlings so that when one ISP link goes down, the other will kick in with out user intervention. USG1900 Thank you
-
Question about routing on zyxel usg 40
Hi, I have network on lan1 (eth1) - 192.168.0.1/24, network lan2 (eth2) 10.212.4.254/29, from eth2 port there is a link (from internet service provider) to remote office 192.168.12.0/24, router in remote office site has ip address 192.168.12.1. I can ping router 192.168.12.1 from eth2: # ping 192.168.12.1 -n -c 3 # ping…
-
Reputation Filter: Categorisation
Hi, We have bought a new ATP500 FW and activated "Reputation Filter" with "URL Threat Filter" (Firmware and signatures up to date). It seems, that quite a few websites (e.g. gui.ipvoip.ch) are not rated and therefore blocked (as recommended). Where can we submit those URLs, so these websites will get rated in the near…
-
Zerobot, USG Flex 100 (W), CVE-2022-30525: something for update sooner than later.
According to Bill Toulas on Bleeping Computer, a new malware named Zerobot is exploiting several CVEs about several products of (again) several brands. CVE-2022-30525 has been declared resolved in May 2022 (according to Bleeping Computer and Rapid7 with firmware 5.21 for all the ZLD 5.x capable devices. So if your box is…
-
USG-110, exclude one specific ip-addresse from being written into the logfile.
My Internet Service Providor has got some new fancy equipment to monitor their network. Unfortuatnly this equipment ping my ip-address every 15 seconds and hence make a line in the logfile 'ACCESS BLOCK' . Is it possible to somehow exclude this specific ip-address - from where the ping comes - from being written into the…
