-
GS1920-48 from 4.50 to 4.70
Hello, I have GS1920-48v2 and upgraded to V4.50(AANZ.3) how to upgrade to 4.70(ABMJ.4)C0 for example. I can't find 4.60 on the site. Kind Regards, Stoyan
-
[GS1900-24EP] Having Wireguard Subnet be on same subnet as LAN
Hello everyone, My use case is that I have two devices that need to be on the same subnet. I am using software called Dante Controller that only works if all clients are on the same subnet. The issue is one device is attached to the network via Wireguard VPN and, therefore, on a different subnet. The two devices: 1. An…
-
XGSXGS1930-52 IP-Settings
Hi, We have 2 XGS1930-52 switches. I have installed the new firmware version V4.70(ABHU.9) 11/04/2024 on the switch. The switch is assigned an IP address via DHCP. However, it is not possible for me to change the IP address from DHCP to a static IP address under IP interface. I get an error message every time, even though…
-
Disable sending LLDP to ISP over fiber link
Hi Sorry for my intensive posting. I am new on modern Zyxel switches and syntax differs a little bit against what I am used to :) Trying to make sure the new Zyxel switch will do what I expect it to before make it production active. Instead of doing this on the fiber port interface to the ISP… no lldp basic-tlv…
-
Zyxel GS1900-24E MIB File for Zabbix?
Is there an MIB file available for the GS1900-24E? Thank you.
-
XGS1250-12 After upgrading to las firmware 2,5GB ports don't work at all
Hi, I've upgraded to the last firmware my Zyxel XGS1250-12 (XGS1250-12_V2.00(ABWE.0)C0.bix) and after doing that and reboot normally, all the ports 2,5 GB don't work at all. Does anyone know how can I solve this? Thanks!
-
Can't login on web gui after firmware upgrade to v2.90 on my GS1900-48HP
If I type a wrong username i can see this message. When the user is correct nothing appears but i get this messages spamming on the network console. Tried resetting the device. After resetting it asks for a password change, then I come back to the previous screens. I can't proceed. Also tried incognito mode, and different…
-
GS-105S v2 QoS implementation
Hi everyone. Is QoS active in both egress and ingress directions on this model? Test reveals it's active for ingress traffic. Any info appreciated. Cheers.
-
Switch MG-108 für Games brauchbar ?
Hallo zusammen, ich habe ein Netzwerk das mit 3 Zyxel Switch MG-108 betrieben wird , an einer 10 GB Internet Verbindung. Vom 10 GB Router gehe ich direkt auf 2 MG-108 die als Hauptverteiler stehen von da geht es unteranderem in unser Büro und Gaming raum auf einen weiteren MG-108 von dem aus es weiter auf 2 PC`s und andere…
-
GS1910-24 VLAN Not Working
Hello, Before I address my issue I would like to tell that I am not a switch specialist at all and that many of the articles listed here in the forum confused me. The switch GUI often seems to differ from SW version to version, many of the screenshots discussed here are not available on my devices. Thus I decided to…
-
[XGS1930] Full CLI access?
Hello, I´d like to get full CLI access on my XGS1930 switch with firmware V4.70(ABHS.1) and local management. Currently if I log with my admin credentials I can only e.g. "show running", but I´m not able to change anything, e.g. "configure terminal" is no possible. I searched the GUI but haven´t found anything usefull. Is…
-
Is it possible to show fiber optics info on XS1930-12HP?
I have an old Netgear prosafe switch. On it I can run… Is it possible to in some way show such info on this XS1930-12HP if moving these SFP+ units fromt the netgear to the zyxel switch? I have Access L3 license. Thanks in advance //Peo
-
Managing VLANs?
Hello, I'm trying to separate 2 VLANs that shouldn't be accessible from one another. Port 1 is the uplink, port 2 a PC on port 8 I'm planning to use a laptop that should have access to the internet, but it doesn't (it gets IP, so I'm half there). This is what I came up with:
-
Missing CLI commands on XS1930-12HP
Hi I am new to this forum. Have used an old zyxel switch before, but now I am back on zyxel again. Just bought an XS1930-12HP. I have just installed it and done some test by configuring some VLAN trunks and other stuff. Seems to work as expected. Interesting that it takes 5-10% CPU when idling though… I have bought and…
-
Zyxel GS1900-24e Original firmware
I recently got hold of a decommissioned Zyxel GS1900-24E from a E-waste recycler, but this switch has been modified to run OpenWrt. Is it possible to return this switch back to factory firmware? I've checked the other boot partition, but it seems to have been wiped. Thanks, Dim
-
Weird Login Screen and Can't Access XGS1930-28HP
Hello, I purchased a brand new XGS1930-28HP switch and am experiencing weird issues with it. Upon removing it from the packaging I placed it on the bench, connected a laptop, and powered it up. After the port LED lit up, I connected to the default IP and tried to log in. It wouldn't take the default password. Tried it a…
-
wifi issue unable to connect it just displaying obtaining or connecting
kindly help me to resolve this issue, i am thinking that its vlan configuration error that device not picking up the ip? its controller or switch issue?
-
Struggling to get VLAN to work
-
GS1900 tagged VLAN nodes drop off after 5 minutes
Hello all. I have a very simple test lab set up, a GS1900-24 with a Win 10 and a Win 11 laptop continuously pinging each other. On the tagged VLAN, these pings just stop after 5 minutes, and the only way to get them talking again is to reset (change, then change back) their VLAN IDs in Windows Network adapter settings.…
-
Xs1930-10 flow control?
Hi. I recently bought an xs1930-10. I'm trying to establish what the default firmware setting is with regards to flow control. I can't see it in any menus on the port setup and I asked support via a question but didn't get a answer either. Does anybody know if its on or off or doesn't exist on default setup? I have…
