-
GS1910-24 VLAN / Trunk-Port
I have a trunk cable (that comes from a router) which delivers the VLANs 40,60,70,80. Now I need to "split" that trunk to individual ports so that I can connect devices there. Devices are not capable to handle VLAN tags, therefore they must be removed on egress. On ingress the VLAN id must be added. I've tried that with…
-
Switch resetou após subir o firmware.
Após subir para a nova versão do firmware, o switch zyxel resetou para default, alguem sabe oque pode ter sido ?
-
Connecting 3 Managed Switches together
Hi, new member here, hi. I have bought for my LAN a GS1900 and 2x GS1200 Now because my router has only 2 ports what is the best way to connect the switches to each other to allow traffic (VLAN etc) to not create a bottle neck. Connecting a cable from #1 to #2 and from #1 to #3? #1 is the main switch (the GS1900) TiA
-
My GS1008HP Zyxel Unmanaged PoE Switch is Overheating
Hey folks! Bought the GS1008HP PoE + Switch. It has 8 ports. I plugged into it my router, an NVR, and 6 PoE cameras from REOLINK. I have all of this in my attic (under the roof). As it started getting warmer here in May this thing either got busted or started overheatting. If i turn it off and turn on later it works but it…
-
Cisco commands equivalent
Hello! I need to make the following settings on multiple GS2210 switches. Kindly tell me if there is any possibility to implement and how. Set enable password Set encrypted password (secret) Following cisco commands equivalent(if any) [no service tcp-small-servers], [no service udp-small-servers], [no service finger], [no…
-
How do I connect my internet service to different VLANS on the GS1200-5?
I have the following settings: ISP modem @ 192.168.10.1 home server @ 192.168.20.250 Wi-fi router @ 192.168.30.50 I thought the following settings in my Zyxel switch would treat the VID10 (internet) as essentially VID 20 and 30 on ports 2 and 3 respectively because I thought that untagged data would essentially be the same…
-
XS 1930 no policy route in ACL?
HI I am trying to setup a classifier and policy route as from the Zyxel tutorial below to forward traffic from one vlan to the other, or deny from one vlan to the other. it was easy to setup the classifier, but then in policy rules, there is no sequence or next hop to define where to send the traffic. So, maybe the…
-
GS1900 older FW?
I've laid my sticky fingers on a decommissioned GS1900-24HP Rev A with FW V2.20(AAHM.0) and would like to get the latest FW for it. As it is not available on the download page, maybe someone here got a copy? Regards, Paul
-
Firmware Upgrade Procedure GS1910-48HP
The release notes with the V2 firmware suggest that the upgrade procedure is to go from 1.00(AABA.0) to 1.00(AABA.2) and then 2.00(AABA.0). Have I understood that you can't go from 1.00(AABA.0) directly to 2.00(AABA.2)? If that's true where can I download version 1.00(AABA.2) to do the intermediate step?
-
Isolate internet facing machine on basic home network
Hi, Apologies in advance if what I'm about to ask is very basic (I've a feeling it is). I've a basic home network. I have one machine that will be outward facing to the internet on ports 80 and 443. Obviously I'm aware that this could potentially compromise my home network without additional measures. So, after much…
-
Switch firmware release-note should mention browser requirement
Requirements for vlient OS and browser for management should be unecessary, but is obviously isn't. I just tried upgrade of a GS1200-5HP v2 switch which then got stuck in "upgrade-mode". Upload of firmware resultet in the error message "Firmware upgrade was failed". I tried 3 different firmware-versions available from the…
-
GS1200-8 Benutzeroberfläche nicht aufrufbar
-
GS1350-6HP-Garage A message could not be handled because it failed to be parsed correctly. Cloud N
I keep this message in the event log and I don't know what to make of it. this switch also drops off line every once in a while making it somewhat unreliable. Now in full disclosure I had to use a PLA6456 to get the network to this garage since trenching for a fiber line wasn't an option and point to point wifi would be a…
-
GS1900-24 - Unable to split switch into 2 different ip ranges, is this possible?
Hi, I asked about this some time ago but cannot find the original thread, nothing I could do would make it work as I would always lose communicaton with the webui and have to reset. I tried again for 6 hours last night with the same results and am once again back using to tplink switches for each ip range. Can someone…
-
xgs2210-52 inter-vlan routing troubleshooting
Dear all, We've configured a stack of xgs2210-52 switches but are running into issues routing traffic between vlans. The environment consists of 2 xgs2210-52 and 2 fortigate 70f connected in full mesh HA fashion, so the switches are stacked and both have a aggregated connection to both firewalls. But we're already running…
-
Can't import self-signed certificate to GS1920-24V2 (FW 4.80, ABMH.0)
Hi, I have a problem to import a self-signed certificate to my switch. I've tried it with a self-signed PKCS#12 file generated from opnsense. File extension is .p12. Then I've tried it with a compiled version from openssl under windows with bothe extensions .p12 or .pfx with and without a password. Whenever I want to…
-
Layer 3 lite XGS1930 series
The difference of Layer 3 Lite is only L3 lite = L2 + static routing ?
-
Technical Specifications
Hi All, I would like to raise some questions regarding the appropriate model of zyxel switch capable to serve the following requirements: Q1. Capable/Supports SNMPv1, SNMPv2 or higher. Q2. Shall be able to accommodate, integrate and provide general traffic handling and management services for at least four (4) different…
-
ZyXEL GS2200-24
How can i reset the switch to default password? and where can i download the firmware for this switch?
-
I need to upgrade the firmware on a Zyxel GS1920-24 switch to version 4.50
I need to upgrade the firmware on a Zyxel GS1920-24 switch to version 4.50. Thanks.