-
GS1910-24 console via factory settings
I do not know the interface IP and user name of the device. Unable to access with 192.168.1.1. I connect with Putty, I do ctrl+c. I am typing the following commands.RedBoot> defaultRedBoot > reset I'm getting an error I don't have much knowledge can you help me in the simplest way putty speed 115200
-
XGS1930-52HP unable to firmware upgrade
All of my XGS1930-52HP are stuck in version V4.70(ABHV.3) | 11/01/2021 (Stable)When trying to update to latest version from Nebula Cloud switch going to downtime for 25 minutes and boot with same firmware again, in event log get error "Upgrade system firmware failed"
-
Pair of XGS1930-28 w/VLANs advice?
My boss acquired two XGS1930-28 with the plan to put one in the cellar with the servers, one upstairs with the desktops, and the idea to run several of our internal networks across the connection with the help of VLANs. Now I certainly understand IP networks, but I've never done anything with VLANs, and after reading up on…
-
STP topology changes
Guys, good morning! We have a switch Zyxel GS2220-50HP model, and the ports are in the "spannning-tree edge-port" configuration. When the port with this same configuration change (turn off), the switch send STP topology changes to the others switches. And this do to the network go down. Can you help me? Regards!
-
XGS1250-12 and SFP+ PM7000-01 XGS-PON transceiver?
Hello, I am trying to figure out how I can skip my Zyxel AX7501-B0 gateway. When inserting the Zyxel PM7000-01 SFP+ transceiver into the XGS1250-12 switch, I get no link and the port status stays down. Inserting the transceiver back into the AX7501-B0, I get link again. Please advice on how to get any kind of debug…
-
GS2200-48 firmware and password
I'm new to the community and would like to thank everyone for their time and effort. I'm just getting back into smart switches. I used to do Cisco years ago using Putty, but had heath issues in 2012 which wiped my memory. A little came back, but most I've had to relearn. So if I post a stupid question that everyone should…
-
XS1930 - SFP 1Gbps
Good morning, I'm planning to move the a full 10Gbps the office ( a dozen of PC, server and workstation) I plan to use initially one XS1930 with 8 10G ports and 2 SFP+ and I have several questions: - could I install the Zyxel XGN100C 10G SFP+ PCIE CPNT card on the server and connect to the switch through the a DAC Cable? -…
-
Current firmware for GS1500-24 switch?
Yes, I know it is end of life but it still works if you use an old browser. My switch has firmware: V1.00(BVN.2)b18.Is there newer firmware and where can I download it
-
Upgrading XGS-1210-12 firmware from a Mac ?
I have tried to upgrade the firmware to the lates version via the web management pages but the switch does not seem to upload the firmware XGS1210-12_V1.00(ABTY.6)C0.bix - it uses C:\fakepath\XGS1210-12_V1.00(ABTY.6)C0.bix as file name file name, which obviously will not work on a Mac although the dialog box on the page…
-
ZON Utility - Invalid administrator password after initial configuration
Hi, I have a problem with ZON utility after first commisioning of switch (tested on GS1920-24v2, GS1920-24HPv2 and XS1930-12F) - after some time it always return me error "Invalid administrator password" when try to perform actions like upgrade firmware, reboot unit, etc. I think the problem occurs after initial settings…
-
latest firmware for XS1920-12 Switch
I need to upgrate the firmware of our XS1920-12 Switch (currently V4.30(AASR.0)), can someone send me the latest firmware available (V4.30(AASR.2)CO or newer) ? If I have to upgrade to V4.30(AASR.1)CO before, I need this version also. Thanks in advance, Knut
-
xgs1250-12 switches, failed auto negotiation on port 9 - 11
Hi there, if I connect a xgs1250-12 to a router with 100M connectivity to port 9, 10 or 11, auto negotiation fails and no connection will be established. If I set one of these ports on the switch to 100M manually, all works fine. Is this a firmware bug?
-
Vlan between a windows pc and raspbian
Hi, I've just bought a GS1200-8 to start experimenting with VLANs at home. I'm trying to make this scenario work: - 2 host - 1 GS1200-8 switch I've created the VLAN 10 on the switch and assigned ports 1,2,3 and 7 to it as untagged. Ports 3 to 8 remains on the default VLAN 1. (see image) Windows PC connected on port…
-
<SOLVED> VLAN: broadcast and multicast packet handling on the XGS1210-12
I configured my XGS1210-12 with 3 VLAN, vlan 1, 17 and 835 (see attached image). VLAN 17 is untagged on port 1-9 and tagged on port 11 and 12.VLAN 835 is tagged on port 10, 11 and 12.VLAN 1 in untagged on port 10, 11 and 12. All is running as expected, but when i checked with packet capture i noticed that the VLAN 17…
-
Why is a DHCP offer not routed by gs1920-24hp to a client on the ap wax510d
Hi everyone I am a bit puzzled about a problem with assigning an IP address to a wireless client. I have configured two static untagged VLANs on the GS1920. VID 1 is the company network, VID 2 is the management network for the WAX510D AP. The wireless client is supposed to be a member of the company network VLAN 1. I did a…
-
Can I look at the MAC table of the switch GS1920-24 Firmware Version V4.70(ABMH.8) | 10/04/2022?
how can i watch it?
-
Zyxel 1930-10 wont reset with ip 0.0.0.0
Hi we're having some network issues and failing to reset the switch manually. The switch is assigning Ip of 0.0.0.0 to all devices and we can see this in the ZON app, however doing a reset to try and change the password to reconfigure the swtich doesn't work.
-
Zyxel 2200-24 won't boot maybe corrupt firmware
Can you please decode this boot loop error message? Is it about firmware corruption or hardware failure of ram/internal flash? Copyright (c) 1994 - 2011 ZyXEL sysExceptionHandler: sysTaskId()=[0x812F51B0], n ame=[PINI] Exception occured!EPC= 0x8014EDE4SR= 0x00007F03CR= 0x50808008$RA= 0x03E00008TLBL Abnormal Stack Task List…
-
Zyxel GS2200-24 L2 Manageable Switch Firmware
Is Zyxel GS2200-24 L2 Manageable Switch Firmware available or not?What is the EOL date of this product?RMA or hardware replacement request can generate or not?
-
GS1920-48HP v4.70 VLAN issue
Hello everyone and please give me your opinion on this problem. I am trying to set up a simple input and output VLAN with number 5, but the configuration is misbehaving. I have a device connected to port 1, untagged port vlan 5. On the output untagged port 45 vlan 5. I set a static IP address on the end device behind the…