-
What exactly does POE option "Disable PD" do?
I have a Zyxel GS1900-24EP. In the options to configure POE for a port, I can select to disable "PD state" (screenshot). The documentation says: "Select Enable to provide power to a PD connected to the port or Disable so the port cannot receive power from the Switch" (p. 132) On wikipedia, there is a table with stages of…
-
GS1900-24 Support
I have a few questions before I help decide should I buy a used GS1900-24 or not. I'm including a copy of the info I have on the item: 1/ Is this product still being supported or is it EOL? 2/ Can I update the firmware to v2.7 3/ Is there a version 2 of GS1900-24 Any help will be greatly appreciated
-
Linking Switches
Hi, I have a GS1920-48HPv2 used unmanaged, I need to link it to a CISCO SG300-28PP is this possible to do via SFP on ports 49 or 50? connecting to the link SFP port on the Cisco? all other ethernet ports are used on both switches. I need to share the internet connection between them so I'm thinking it will have to be done…
-
uplink GS-1920-24 v2 switchs
Hello everyone, I need advice to connect 2 GS1920-24 v2, with transreceiver modules and a fiber optic cable about 100m long. I just want to know if it is possible to do this with Zyxel SFP-SX-D modules. Thank you
-
Unmanaged Switch MG105 - ping ok, internet ko
Hi my switch mg-105 suddenly won't let me browse the internet. I can ping the router or other devices, but internet is down. If i connect the pc directly to router, internet works. Suggestion? Thanks
-
Need some help with IGMP Snooping settings on GS1900 switch
Hi, I just purchased a GS1900-16 switch and one of the requirements for the audio system we're using (Wheatnet) is that we enable IGMP snooping. They have some specific settings, but the information provided is for Cisco switches and I am not totally sure of the associated configuration settings for Zyxel. I'd really like…
-
GS2210-8 firmware please
Please provide firmware for the GS2210-8. The link here does not work for me: https://community.zyxel.com/en/discussion/5356/switch-gs2210-series-v4-50-patch-3-firmware-release
-
GS1910-24 VLAN / Trunk-Port
I have a trunk cable (that comes from a router) which delivers the VLANs 40,60,70,80. Now I need to "split" that trunk to individual ports so that I can connect devices there. Devices are not capable to handle VLAN tags, therefore they must be removed on egress. On ingress the VLAN id must be added. I've tried that with…
-
Switch resetou após subir o firmware.
Após subir para a nova versão do firmware, o switch zyxel resetou para default, alguem sabe oque pode ter sido ?
-
Connecting 3 Managed Switches together
Hi, new member here, hi. I have bought for my LAN a GS1900 and 2x GS1200 Now because my router has only 2 ports what is the best way to connect the switches to each other to allow traffic (VLAN etc) to not create a bottle neck. Connecting a cable from #1 to #2 and from #1 to #3? #1 is the main switch (the GS1900) TiA
-
My GS1008HP Zyxel Unmanaged PoE Switch is Overheating
Hey folks! Bought the GS1008HP PoE + Switch. It has 8 ports. I plugged into it my router, an NVR, and 6 PoE cameras from REOLINK. I have all of this in my attic (under the roof). As it started getting warmer here in May this thing either got busted or started overheatting. If i turn it off and turn on later it works but it…
-
Cisco commands equivalent
Hello! I need to make the following settings on multiple GS2210 switches. Kindly tell me if there is any possibility to implement and how. Set enable password Set encrypted password (secret) Following cisco commands equivalent(if any) [no service tcp-small-servers], [no service udp-small-servers], [no service finger], [no…
-
How do I connect my internet service to different VLANS on the GS1200-5?
I have the following settings: ISP modem @ 192.168.10.1 home server @ 192.168.20.250 Wi-fi router @ 192.168.30.50 I thought the following settings in my Zyxel switch would treat the VID10 (internet) as essentially VID 20 and 30 on ports 2 and 3 respectively because I thought that untagged data would essentially be the same…
-
XS 1930 no policy route in ACL?
HI I am trying to setup a classifier and policy route as from the Zyxel tutorial below to forward traffic from one vlan to the other, or deny from one vlan to the other. it was easy to setup the classifier, but then in policy rules, there is no sequence or next hop to define where to send the traffic. So, maybe the…
-
GS1900 older FW?
I've laid my sticky fingers on a decommissioned GS1900-24HP Rev A with FW V2.20(AAHM.0) and would like to get the latest FW for it. As it is not available on the download page, maybe someone here got a copy? Regards, Paul
-
Firmware Upgrade Procedure GS1910-48HP
The release notes with the V2 firmware suggest that the upgrade procedure is to go from 1.00(AABA.0) to 1.00(AABA.2) and then 2.00(AABA.0). Have I understood that you can't go from 1.00(AABA.0) directly to 2.00(AABA.2)? If that's true where can I download version 1.00(AABA.2) to do the intermediate step?
-
Isolate internet facing machine on basic home network
Hi, Apologies in advance if what I'm about to ask is very basic (I've a feeling it is). I've a basic home network. I have one machine that will be outward facing to the internet on ports 80 and 443. Obviously I'm aware that this could potentially compromise my home network without additional measures. So, after much…
-
Switch firmware release-note should mention browser requirement
Requirements for vlient OS and browser for management should be unecessary, but is obviously isn't. I just tried upgrade of a GS1200-5HP v2 switch which then got stuck in "upgrade-mode". Upload of firmware resultet in the error message "Firmware upgrade was failed". I tried 3 different firmware-versions available from the…
-
GS1200-8 Benutzeroberfläche nicht aufrufbar
-
GS1350-6HP-Garage A message could not be handled because it failed to be parsed correctly. Cloud N
I keep this message in the event log and I don't know what to make of it. this switch also drops off line every once in a while making it somewhat unreliable. Now in full disclosure I had to use a PLA6456 to get the network to this garage since trenching for a fiber line wasn't an option and point to point wifi would be a…
