-
XMG3927-B50A Connect to FTTP (Full fibre)
I have a ZYXEL XMG3927-B50A connected to a FTTC setup with TalkTalk. My Zyxel then connects via (cat5e and cat6 cable) to 2 other routers as AP connection. My setup works great The parental control work via the Zyxel throughout my system and get great coverage/signal. Im due to change over to a Full Fibre Connection FTTP…
-
GS1200-8 802.1Q VLAN: Must all ports be connected to VLAN 1?
I wanted to separate a PC into VLAN2, but it should also be able to connect to the same internet router as for all other devices in VLAN1. I set the PVID to 2 for this PC/port and set untagged for VLAN2 and unconnected for VLAN1. Also I put the the internet router as untagged in both VLANs. But with this it cannot connect…
-
Packet loss on GS-4024 with VLAN
Hi! I have configured a GS-4024 with VLAN, but I have packet loss and it's acting like he is making pauses. I cannot find any info on the internet. Here is a part of the config file:; Product Name = GS-4024 ; Firmware Version = V3.80(LL.4) | 10/06/2008 ; SysConf Engine Version = 1.1 vlan 1 name 1 normal "" fixed 1-24…
-
May I get a firmware(for VES1724-56B2)?
Hello. We have been operating the switch(for VES1724-56B2 model). The problem in us is that we do not have any firmware file to restore. Do you mind if I ask that we can get a firmware(for VES1724-56B2)? - I could not find a firmware(for VES1724-56B2) in myZyxel-device management-firmware download. Thank you Adan Regard
-
Is this a good 16 port gigabit switch? If not, what are some good recommendations?
I don't have gigabit internet but want to future proof this purchase. Also, do I connect the ethernet wire from the modem into any of these slots, and then I connect a Ethernet wire from the switch to the router? Or do I cinema hd connect the ethernet wire from the modem to the router, then a wire from the router to any of…
-
GSP1500-24P
Hello All, I have 2 questions about this unit.... is it possible to see by port #, or MAC, what is the assigned IP? very often, if there is a pwr failure or the ISPs modem rebooting, the switch is not picking up the correct IP, and the connected devices won't go online. Is there a fix for this in GUI or is it possible to…
-
General Networking Question
PBR takes precedence over the routing table. But how do we check if it is working?
-
XGS4600-32F - SFP port issues
We have an issue on some switches. Transceivers stop transmitting or/and corrupted info from it. Port : 5 (SFP)Vendor : ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒Part Number : ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒Serial Number : ▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒▒Revision : ▒▒▒▒Date Code : 20▒▒-▒▒-▒▒Transceiver : OthersCalibration : InternalTemperature(C) ++ 21.00 0.00 0.00 0.00…
-
How to prevent SNMPv3 priv user configuration from differing on each backup
I have a GS1900-24 and use oxidized to backup its configuration in git. Even when I do not make any changes on the switch, the SNMPv3 configuration for privacy encryption on the admin user keeps changing. I'm unnecessarily filling my repository as a result. I am specifically referring to this SNMPv3 configuration line in a…
-
Vlan Trunking and IP route Configuration GS2220-28HP
Hello, new to zyxel,How do you configure trunk and allow the vlan on a trunk port? and how do you add static routes? Regards,
-
Mac Pro and XS1930-10 link aggregation
Hi, I am trying to aggregate both mac pro ethernet ports that I connect to the XS1930-10 switch. I am creating a "virtual link aggregate" on mac pro, as per instructions found on Apple's wikis, but it is not working. I mean the aggregate bond is created OK on the mac pro, but it never gets just one IP and get online. I…
-
XS1930-10 to XS193012-HP SFP+ Link aggregation
Hi, Is it possible to XS1930-10 to XS193012-HP SFP+ Link aggregate? I have connected both SFP+ ports on both switches, and they seem to be up, but when I go to Nebula I can see on the XS1930-10 that one of the two SFP+ ports is "STP blocking" status, and the other SFP+ port is marked as "Uplink". On the XS1930-12 none of…
-
Multiple 4600 switch connected to 4600 Stack Switch
I got Multiple 4600 switch connected to 4600 Stack Switch. Let's name the 4600 stack switch - physical switch X and physical switch Y respectively. I have 4600 switch A connected to both switch X and switch Y. I also have 4600 switch B connected to both switch X and switch Y. How do I configure switch A go to switch X as…
-
The ZON download page does not work.
https:://www.zyxel.com/form/zon_utility_download.shtml After entering your information it is suppose to send you a link. It does not. I've tried on various email platforms, personal home, and our corporate office. Each of these their own mail system and are independent of each other. In every case no link was ever…
-
XGS4600-32F Default Configuration file?
Hi, I'm trying to reset a switch back to it's factory default settings via the console port, however it says I need to upload the factory default configuration file, but I don't know where I would get this config file from? Sorry if it's a stupid question, but if anyone could help me out that would be very much…
-
GS-1100 No Communication
I have a GS-1100-16
that every time there is a power outage it powers ON but the communication from
the ports. Is there a way to reset it to get back functioning?
-
DHCP Servers, DHCP Relay, VLAN and VoIP Configurations
Dear Zyxel Forum I have the diagram below. I would be very thankful if some
experts here help me how to configure: 1. DHCP Servers 2. DHCP Relay 3. VLAN and VoIP Thank you very much
-
non-PoE device only has PoE connection on GS1900-8HP
Hi,I have a Ikea Gateway that seems to have an issue with the switch. It has a PoE connection, but no data connection. The Gateway indicates not to have data and this is confirmed in the Web UI of the switch. The PoE status can be confirmed through the light and the Web UI. The port counter shows no data to be…
-
Can Uplink port be used as part of the LAN (XGS1930-28HP)?
The XGS1930-28HP has 4 Uplink ports, one of which I am currently using to connect to the 10Gb router. Since the rest of the (LAN-) ports are max 1Gb, I was wondering if I could use one of the unused Uplink ports to provide a 10Gb connection on the LAN for one specific workstation. Thanks for any insights HF
-
How to control POE of GS1920-24HP
Hello, Is there a way to control POE state of individual ports? I used to have an HP switch where it was relatively easy to manage via console 'no' commands. Switch is GS1920-24HP and firmware is 4.50
