-
NWA210AX - Transmit power stuck to 16dBm or 22dBm in 160Mhz
Hello I have a NWA210AX wifi access point. I live in Switzerland and the channels 100 to 140 can legally be used at 30dBm (1000mW), while the channels 36 to 64 can be used at 22dBm (200mW). So it should be possible to run on channel 120 with 160Mhz with the full 30dBm of power, if my understanding is correct. However, the…
-
DCS on NWA50AX is selecting the channel with highest interference probability and ignores empty ones
Hello, I have just received NWA50AX and I am testing that for some quite specific use cases where good automatic channel selection is very important. Especially on 5GHz However, the behavior is quite strange: At current location, there are 3 other APs in range: * Ubiquiti: 40MHz@channel 38 (far away) * Ubiquiti:…
-
Moved: Come disabilitare salvataggio nel cloud
This discussion has been moved.
-
Zyxel SP300E printer connected to N4100
I installed a ZyXEL N4100 with the SP300E ticket printer a back in 2014 before I retired. All has worked well since. I recently bought off eBay a (so they said) new SP300E printer as the old one was getting faint. How do I set the IP address of the printer? I did see this once but can't remember how to access the printer.…
-
WAC6552D-S settings
Dear Zyxel, I bought a WAC6552D AP, but I can not connect to it. I registered in a Nebula system, but unfortunately it is offline. If I searched for in the network and pressing the allotted IP address I will get this message: "This AP is managed by AP controller. To manage this AP, please access AP controller's web…
-
Problems with LAN and wireless LAN!
Hello, and thank you in advance for any assistance. My current laptop is an HP Probook 4545s, and neither my wireless LAN nor my wired ethernet LAN work. I've tried connecting to a number of different computers, but none of them have worked. I tried installing a new Wireless LAN driver, but it didn't help, and I couldn't…
-
NWA1123-NI 404 Not Found Error after factory default
I recently factory defaulted my NWA1123-NI AP using the reset button on the bottom of the device. i can see the AP has gone back to its default 192.168.1.2 however when i try to web brose to the AP the page says 404 Not Found. File Not Found. I have used the ZAC utility software which finds the AP but cannot configure the…
-
ZyXEL NWD6602 Dual-band Nano -WiFi-adapter
can i share my phones internet to this
-
Router(config-wlan-radio test_24G)# output-power 50% % Command removed due to the platform upgrade.
How to solve the problem?
-
Diffrence between NWA50AX and WAX510D
Hello all, is there a comparison list for Zyxel APs? If not, what is the difference between the above APs? Thank you very much for your help. Greetings Oliver
-
nap102 works But nwa1123ac doesnt work
I put on the same port. NAP102 works and can get ip and surf internet. nwa1123ac no works, cannot get ip, cannot surf internet. Pls help troubleshoot.
-
802.11k (Assisted Roaming) on NWA210AX (and likely other models)
Hello, I just got my second NWA210AX. I have two of these configured identically with regard to SSID/security etc. My devices jump from one to the other as expected (different floors of my house). I have 802.11k/v enabled on all SSIDs on both APs. Running newest available firmware (6.25). They are both running standalone…
-
Where can I buy power adapter for WAX610D
Hello,Would anyone kindly advise/recommend the type of power adapter for WAX610D ? Appreciate if you could share some experience on this. Have thought of buying a managed PoE switch that support 2.5GbE, but probably a managed 2.5GbE switch + Power adapter is a better choice? Thanks
-
NWA210AX cannot choose UNII-3 channels
Rather confused to find I cannot choose a Band C channel considering these have been license free in the UK for a few years now and is the only range that allows 80Mhz channel width without DFS. Is there a particular reason this is not supported?
-
NWA 5121-IN repeater
Hello I have NWA 5121-IN and I want to use them as a repeater for my wifi modem I setup everything and the NWA 5121 connected to my modem device but there is no internet connection and one thing more I noticed it's only take ipv6 Tried to upgrade firmware and same The question is can I use them as a repeater for other wifi…
-
WLAN AP surveillance by alert log?
From time to time (once or twice per month) we experience a WLAN/AP failure. But the administrator get notice of it only when a user is notifying him that he cannot connect. In that case we have to manually reboot the AP (we've got only 1 AP connected and operated by USG110) and all is fine again. We are aware of the…
-
Networking issue with Zyxel WLAN Controller and VLANs
I'm kinda stuck with this issue, customer reported some screenshots from his iPhone, which doesn't really give away much information, but before I travel three hours to the customer, maybe somebody of you have an idea. I have a Zyxel NXC2500 (WLAN AP Controller), which I recently reconfigured with the Zyxel-Wizard. This…
-
WAC6303D-S partially defective
Hi, I have a WAC6303D-S AP which one day occurs as offline from the VPN100 AP information view. I did a replacement, and decided to take a close look, since LED indication somehow seems correct. I am not able to reach the AP via WEB GUI, it's not aquring IP via DHCP, and not answering via standard IP. However it is…
-
Change Management VLAN ID on WAX610D disrupts SSID in VLAN1
For an existing network I'm implementing a bunch of WAX610D(30 pieces) with controller on Flex 500. On the Flex 500 I've configured VLAN88. There are 2 SSID's:- Internal LAN with VLAN tag 1- Guestnetwork with VLAN tag 88 with only internet access So far so good everything works, guestnetwork works fine. But to save IP…
-
NWA1123ACv3 managed mode
Hi, We bought 6 NWA1123ACv3 access point thinking they will replace the NWA1123ACv2 but it seems that we cannot manage this new modèle from USG40w. Please is there a way to make the NWA1123ACv3 manageable capwap mode with the USG40W ? Thanks !!
