-
diaginfo file tar.bz2 - How to View???
I have a NWA1123 AC HD that is giving me difficulty in connecting to the network & Nebula @ 1Gb rather than 100Mb that it is connecting to. It is connected to Nebula but showing only @ 100Mb. I have just logged into it as admin and went to Diagnostics and downloaded the daiginfo-xxx.tar.bz2 file. How do I read or view this…
-
AP appears offline
Hi there, Sorry if my question is dumb, I am new to Zyxel. On a NXC2500, 4 APs seams to be offline. The one with no IP address is dead and physically disconnected, but the 3 others are connected and pingable. I've restared 192.168.10.7 but still appears offline. All the buttons are greyed out when I select one. What should…
-
V6.25(P2)C0 Release is out for 24 current APs. Manual load options for ACs?
Accumulated bugs fixed. Known Issue Mode
Known Issue
Cloud Only: 1. [eITS: 210400642]
[Symptom] Mesh SSID is visible 2. [eITS: 210500147]
[Symptom] SSID not broadcast after
changing the forwarding mode from
NAT to local bridge For Cloud, Managed, and Standalone 3. [eITS: 210900596]
[Symptom] Act-session ID in access
stage…
-
How to restart automatically ZyXEL AP every day ?
I have a Zyxel USG 110 (firmware V4.65) and I would like to restart automatically the access points (NWA5123-AC-HD) every day. What's needed for this operation? How can I setup this restart?
-
Does WAX510D support 40MHz on 2.4G?
I set my USG60W as the
controller for WAX510D and set the 2.4G to 20/40MHz but when I view WiFi
from more phone I don't see it show that its running in 40MHz? I see
my NWA1123-AC-HD run on 40MHz. Not too big of a deal
if it only supports 20MHz just thought I check.
-
Ceiling mount plate for WAC6503D-S
Where can I inquire about getting a ceiling mount plate for the WAC6503D-S?
-
Will NWA1123-AC-HD get wpa3 ?
Will NWA1123-AC-HD get wpa3 in standalone? Thanks
-
Shutdown AP from USG/NXC
I know you can reboot a managed AP from the USG. You can also do it through the CLI with CAPWAP. Is it possible to shutdown an AP from a USG/NXC? Seems like the only way is for the AP to be in standalone management mode.
-
NAS 326 CLI manual
Is there a manual that lists cli commands along with sample code Thanks
-
nwa210ax & PoE12-HP. PoE not working.
Hi, i recently bought an nwa210ax AP, and I wanted to power it over POE. So I bought a PoE12-HP. It is the suggested Poe-injector on Zyxels own productpage for the AP. But all I get when connecting them together is the AP flashing green/orange for a while and then turning itself completely off. I have tried several cables…
-
Stock firmware for 3510-b0
Hi I have a Zyxel 3510 and all I have is a red light. I bought this from my former ISP and I need an image and Tftp instructions because I assume that it's bricked.
-
NWA1123-AC-PRO SNMP MIB variables not incrementing
I have a NWA1123-AC-PRO and I am trying to monitor interface performance using SNMP. I am able to query the ifInOctets MIB variables, but the values rarely increment. When they do increment, it is one brief jump, then they freeze again. Traffic is flowing normally through the AP, so the counters should be going up. The AP…
-
[Videos] NWA50AX Access Point – Your simple path to WiFi 6
NWA50AX AP is specifically designed for use in small business,
SoHo, and home offices. Comes with the right-feature fit for small business
networking, NWA50AX is an indoor WiFi 6 AP for small business owners looking to
upgrade to 11ax (WiFi 6) without an expensive price tag. No networking expertise required - The NWA50AX…
-
NXC2500 - Firmware update
Hi, I want to update my ZyXel NXC 2500 - wireless lan controller. ZyXel NXC 2500 Firmware: -Start module: V1.02 -Current version: V5.00 (AAIG.3) -Release date: 2017-02-03 The ZyXel is registered in the "myzyxel.com" platform but it does not appear in the "Firmware download" tab (this hardware may not be supported by this…
-
Mesh of three Zyxel WAX610d-accesspoints suddenly stopped working
We're no networkingspecialists, but after a long consideration we replaced our three Cisco AP's from 2016 with three AP's from Zyxel (WAX610d for wifi 6 etc.) this spring. Installing took some time for us amateurs, but it worked fine until last Friday. Since then we are in the dark of what happened and more: how to fix it.…
-
uplink currently operates at a lower speed 100 Mbps
Hello all, Sorry if my questions are stupid but i am a novice. I just bought 2 NWA210AX and installed them in my home in order to have a good wifi signal on ground floor and first floor. My 2 devices are directly connected to an ethernet cable with POE. I activated the AP smart mesh. On the access point board, one of my…
-
Dead Wireless?
It appears that my wireless NWA210AX is dead. I tried different PoE+ switch ports. It will no longer power on. It was working fine yesterday. Today is dead, no LED lights on. My entire network and another old AP is running fine for my IoT/Garage. This is Last purchased Feb 19, 2021. Not even a year old.
-
seamless-wireless-roaming
Hello, I have a number of WAC6103D-I setup through a number of warehouses and the users are losing connection when walking from one AP to another. I want to setup seamless Roaming but cannot find the settings on the firmware to offer this. Can anyone point me in the right direction? Thanks
-
VPN100 and NWA5123 download very slow
Hi, I have many problem with VPN100 configuration. My customer have 35 nwa5123 + 3 WAC6303 connect to VPN100 controller. When I do speed test my download is 30 Mbps max. My lan cable speed test download is around 580 Mbps My internet fiber is 1,0 Gbit synchronous in download/upload. I removed one single nwa5123 to vpn100…
-
NWA1123-ACv2 get certificate failed connecting with Nebula
Dear all, I have some 10 NWA1123-ACv2 APs on site, all is going perfectly fine for them and it works great with Nebula. For my last AP i'm facing a problem, it won't connect with Nebula; into the NCC Discovery tab the error message is This access point is not connected to the Nebula. ( Get certificate failed ) For this AP…