[NWA130BE] Since 7.20, iPhone 16 toggles between WiFi and Celluar

Options
1234568»

All Replies

  • gagadget
    gagadget Posts: 5
    First Comment Friend Collector
    image  Freshman Member
    Options

    Dear all,

    (Sorry for multiple posts above don’t know how to delete them)

    So far my iPhone 16 had no more issue with the parameters tuned in octobre the 22th.

    May I publish them ?

  • Flachzange
    Flachzange Posts: 26
    First Comment Friend Collector First Anniversary
    image  Freshman Member
    Options

    Sure as long as they don't include credentials or other sensitive data.

    But also be aware: I don't see that issue so often anymore. There were times when I thought it is gone and then a minute later it was there again.

  • Zyxel_Melen
    Zyxel_Melen Posts: 5,273
    Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate
    image  Zyxel Employee
    edited November 18
    Options

    Hi @Flachzange @matradix @Maverick87 @gagadget and all ,

    Sorry for the long wait. Our team compared the packets you shared and found a way to replicate this issue.

    Symptoms and possible triggers:

    The phone repeatedly connects, disconnects and reconnects to Wi-Fi, so it may keep switching between Wi-Fi and cellular. It typically happens on the 6 GHz band, under either of these conditions (or both at the same time):

    The phone judges the Wi-Fi connection quality to be poor, even though the signal strength is still normal (around -70 ~ -75 dBm).
    The phone is roaming from the 5 GHz band to the 6 GHz band.

    Phone and AP behavior:

    In both cases the phone tries to reconnect, but the AP still considers it connected, so the AP sends an SA Query. The phone does not reply, so the AP disconnects it, and the phone keeps retrying. In the AP log this shows up as “Partner STA already exist” followed by SA Query timeouts and peer deletion. The first message alone is normal housekeeping. It becomes a problem only when the pattern repeats and the phone does not recover. A full disconnect and reconnect, such as moving away from the AP and coming back, recovers it.

    Firmware improvement:

    We have confirmed a date-code firmware that reduces the issue of iPhones frequently switching between Wi-Fi and cellular.

    V7.40 Patch 2 alone does not fully resolve it. Some users(like @gagadget) report it works well after tuning the radio settings and enabling Smart Steering, which lets the AP disconnect clients before they try to reconnect. The settings below worked for them, and you may adjust them to your environment if you want to try it first:

    TX power: 20 dBm (5 GHz) / 30 dBm (6 GHz), so 5 GHz does not mask 6 GHz.
    Smart Steering: thresholds of -72 dBm (6 GHz) and -75 dBm (5 GHz), both with High aggressiveness, so the handoff happens before the signal gets weak.
    WLAN rate control and band select(optional): minimum data rate of 24 Mbps (5 GHz / 6 GHz), Band Select disabled, and 802.11k/v/r/d kept enabled.

    If the issue still occurs, please send us the diagnostics file and issue timestamp.

    Zyxel Melen


  • jpblanch75
    jpblanch75 Posts: 188
    First Comment Friend Collector Fourth Anniversary Community MVP
    image  Master Member
    Options

    Any time I use Smart Steering I have issues. Forcing the device off the network does not help me as it causes other devices not to work properly.

    My network is split into two. 2.4ghz is one SSID and 5ghz/6ghz is a other.

    The iPhone is my work phone and I don't use it as much when I'm home but I have not really seen the issue as of late and it could be how I have mine setup. I do use nebula and not stand-alone mode. I don't pay for anything extra on nebula.

  • Zyxel_Melen
    Zyxel_Melen Posts: 5,273
    Zyxel Certified Network Engineer Level 1 - Switch Zyxel Certified Network Administrator - Switch Zyxel Certified Network Administrator - Nebula Zyxel Certified Sales Associate
    image  Zyxel Employee
    Options

    Hi @jpblanch75 ,

    Thank you for the feedback. The Smart Steering values we shared were a workaround for the time before the date-code firmware was available. We recommend trying the date-code firmware first instead of adjusting Smart Steering, so please keep Smart Steering disabled for now. We have sent you the date-code firmware in a private message.

    Please also note that if the Smart Steering threshold is set too high (for example, above -70 dBm), the AP may disconnect clients too aggressively, which could affect other devices as well.

    If the issue happens again, please send us the diagnostics file and the timestamp of when the issue occurred, so we can look into it further.

    Zyxel Melen