-
Nebula 19.10 - Switch "Port advisor" widget
Hello everyone, I see a new widget inside Nebula portfolio. I tried it inside an ORG of mine, and I see this: While I have there some PoE devices, I see there is zero value on PoE line. I suspect that PoE detection could lead to some PoE errors… is it available some documentation on this widget?
-
Multiple providers
Good day! Thank you for your answers to the previous questions. Now I have encountered the fact that having several providers, I have micro switches between them, which lead to a break in communication. Tell me, where can I correctly configure the broadcast of a certain LAN zone to the provider I need? Now each provider is…
-
FWA510 drops connection after a few hours
Just got a FWA510 and been trying to use it over the weekend. After the unit has been turned of for 3-4+ hours it starts dropping the connection, I'm guessing it's loosing connection to the mobile network after looking in the logs. Once it starts dropping the connection it will keep on doing it randomly several times an…
-
Nebula 19.10 - Topology error
Hello everyone, I have this issue: As you can see I have 7 devices that (looking at the Topology graph) seem to be linked directly to the firewall while they are connected to switch2 that you can see below. I have the firewall -> first poe fiber switch1 to APs and double DACs to switch2 -> switch2 for everything else. All…
-
Firmware upgrade from Nebula 19.10 - error with XGS1930-52HP
Hello everyone, I tested the firmware upgrade option from Nebula 19.10 to newest hardwares' firmwares. I tested APs, switches and firewalls. Everything seems smooth, except with XGS1930-52HP: I tested it twice. As you can see here: And here The "last upgrade time" is updated but no firmware update was completed…
-
Drastic throughput drops recently.
Until the last week or so (when one of my APs bricked itself, and I had to buy a replacement) I was able to get my full bandwidth on speedtest.net (approx 420mb/s) if I was in the same room as one of my NWA130BEs, and throughout the house I was able to get between 100% and 70% of the bandwidth. Recently, I am getting less…
-
High Ping & Slow Wi-Fi on NWA50AX Access Points – Wireless Only
We are facing high ping latency, slow speed, and unstable wireless performance on our site "Office". We are using four Zyxel Nebula NWA50AX Access Points (2 per floor). Issue: Wireless users experience: Ping spikes over 1000 ms (even to our own gateway) Packet loss Slow speeds Wired connections are stable. Actions Taken:…
-
"Remote access VPN" in Nebula not visible
Hello community, we have a "Zyxel USG Flex 100HP" and want to provide Client-to-Site VPN. We have read in a couple of documentations / articles that its possible via Nebula e.g.…
-
USG Flex 200 allow a specific URL
Hi, We have a need to allow a specific youtube URL like: https://www.youtube.com/watch?v=cOG7j9C4kVs&ab_channel=FazendoNerdice on top of our security policy that blocks the youtube as a whole. Is it possible to accomplish this using an USG Flex 200 registered on Nebula?
-
WPA Enterprise using cloud auth and EAP-TLS?
Nebula AP with WEP Enterprise and cloud auth is currently using the insecure PEAP-MSChap2? Can it be configured with EAP-TLS?
-
Blank widget for Security Router family
Hello everyone, I have an Organization with a blank widget: There should be written the MAC address of the PC that triggered the filter but it did not show it. I see it only clicking on the widget:
-
Problème interface Gui
Je n'arrive pas à accéder à l'interface gui du routeur scr50axe en wifi ni par le port lan 1.2.3.4 Merci d'avance
-
NWA130BE not responsive
I have two NWA130BE that have been working fine. Today I needed to upgrade the firmware and the main (gateway AP) updated and works great, but the second wireless AP (dining room AP) is not showing as online, but the LED is solid green. I have tried power cycling and resetting but I am not able to get it responsive. The…
-
VPN site-to-site from Nebula device to another ORG
Hello everyone, I have some needs when I need to send all the traffic from a Nebula device to another ORG: I need to set a VPN from Nebula to another site (Nebula or not…). I need to set NAT Traversal in Non-Nebula VPN parameters I need to establish a full tunnel VPN I have different devices, security routers and…
-
How to enable IPv6 on USG 100 FLEX
Hello, it's possible to enable IPv6 on USG 100 FLEX using nebula? Already saw that nebula don't support IPv6 configuration and it says to enable it on Firewall Interface, but the option also don't appear on web interface.
-
USG FLEX PPPoE Connect
Hello! I encountered a problem with the PPPoE connection on the USG FLEX 700H router I chose port 3 as a test port and configured the VLAN 20 configuration + username and password on it. But the equipment did not receive any DHCP address Can you tell me how to analyze the problem and find a solution for the connection?
-
50h antimalware
an question which i have allready for a long time, but i can't find an answer for it. We have an flex50h, which has to do with antimalware. We have an gold license on it. Antimalware is enabled, but i'm realy wondering if it is doing anything. No eventlogs at all, i can download eicard files for example. Nothing. nothing…
-
API
Another question about API. I really hope this is not correct. But is it true that i cannot read the eventlog from an flex 50h through the API? that would be very disapointing. It means we almost cannot create tickets of those firewalls in our system. If it's not possible yet, when will it be available do you think?
-
Wireless SSID not visable
Yesterday i had an strange thing. i have 3 wifi networks. but i just can find 1 (on both laptop as phone). all networks are enabled, and offcourse not hidden SSID. I didn't have time to investigate it yet, but i see this in the logging: 2 ports control blocks? what does this mean? Can it has something to do with it? I will…
-
Measuring cellular signal FWA510
I have some issues with losing connection to the cellular network with my FWA510. According to the Nebula app the cellular signal is -97 dbm. I will try to install an external antenna, but I wonder if I can get more info about the cellular network from the app? Is it using the 4G or 5G network for example.
