-
XS1930-12HP Questions on its SFP+ Ports
i see that the XS1930-12HP has two sfp+ ports, i have some questions: do the ports support speeds other than 10G ? can we use GPON SFP modules like this one with this switch ? Thank you.
-
How to securely add a switch in front of the firewall--and which switch you recommend?
The ISP is giving us one port on their switch for Internet, but we have two firewalls (separate organizations needing to share the same Internet) that we need to plug in. I'm looking to put a switch behind the ISP switch and in front of the two firewalls. We use Nebula. I think I'm looking for a small Nebula switch—only 4…
-
Zyxel gs1910-24HP v2
i recently got my hands on this older model great for my home network with the POE functionality but the issue i am running into is that i like to configure this switch and i cant find the right documentation for the version i have. i can find the manual for V1.0 but the software on this switch is V2.00(AAAY.0)C0 and i…
-
How to configure Voice VLAN on Zyxel Switch 1920
I have set the VLAN Voice VLan 30 Ports 5,6,7,8 are tagged and is untagged for data traffic I noticed I have to set up OUI Mask and address but its failure on all permutations MAC Address 9C:75:14:07:CF:76 Vendor Wildix srl Block Range 9C:75:14:00:00:00 - 9C:75:14:FF:FF:FF
-
XS1930-12HP dashboard shows SNMP Off when it's actually ON
Hi, Is there a bug with firmware V4.80(ABQF.3)? The dashboard is displaying that SNMP is OFF but it's actually ON and working. The community string has been changed from the default. It's been like this for a while, I think since upgrading to the latest firmware but haven't reported this until now.
-
Zyxel XGS4600, set lower mtu
Good afternoon I have an XGS4600 switch and another switch (HP) that need to be paired at the VLAN level. I configured 2 VLANs, gave addresses to both switches, everything works ok. However, by the time of installation in the product network, it turned out that there would be other equipment between the switches in bridge…
-
Help Needed With Configuring VLANs on GS1900-24 Switch
I'm having issues setting up VLANs with my Zyxel GS1900-24 switch. I have currently two VLANS running through the switch: VLAN 1 (the default) and VLAN 20 (which is for my guest network). Frames are tagged by my WAPs and passed through trunk ports on a small Netgear switch (for POE purposes) and all traffic comes into a…
-
alternate failed log in
If, alternately, I put http://setup.zyxelinto the brower I do get the login screen for the Zytel switch, BUT even though I have held the reset button for minutes, it will NOT accept the default values and I can not log in - so can NOT do ANYTHING with switch. Help, please!
-
Link Aggregation - 10G & 1G
Hi, I have a PC with a 10Gbe NIC and a NAS with a 10Gbe NIC and two 1Gbe NICs. If I connect both 10Gbe NICs to the Zyxel switch as well as my TV, someone can watch something on the TV streaming from the NAS. If I then copy a large file (a 4K film for example) from my PC to the NAS, it often causes the connection from the…
-
GS1910-24HP how to configure VLAN`s ?
Hi, I'm trying to setup VLAN`s on old GS1910-24. Device info: Software Software Version V1.00(AAAY.3) Software Date 2013-03-05T10:42:04+01:00 Code Revision 40c11c4fd061 Unfortunately in VLAN Port Configuration I cannot add all VLAN`s like I saw in other Zyxel switches At the moment AP`s keep getting IP`s from the range…
-
Fan speed control on Zyxel switch?
I have a 48 port variant of the Zyxel managed switch. It's in my garage which is very cool in temperature, especially this time of year (very wintery October/November) around 50°F. Currently, I have found no way to control the fan speed which seems to be full throttle all the time. I get the reason is to prevent…
-
Power usage increase on XGS1250-12 V2 firmware
Hi, I upgraded the firmware of my XGS1250-12 from V1.00(ABWE.3)C0 to 2.00(ABWE.0)C0 and now the power usage has increased. The green graph is the time left on my UPS and it has decreased significantly. Anyone else seen this?
-
Download latest firmware for GS1200-8 and GS1200-8HPv2
I cant download those files. Seems i dont have access. Could you please make them public available? https://community.zyxel.com/en/discussion/9591/fixed-gs1200-8-8hpv2-management-ip-address-issue/ thanks Simon
-
Small HomeLab network system
Hello! I have an idea to use these devices for my HomeLab and manage it through NebulaFLex. I already have MikroTik Chateau LTE router. Switch GS1915-24EP - 1.pcs + Access point NWA50AX - 3.pcs + other RJ45 connections - 8pcs. and some time later 6 security cameras might be added but for that my idea is to use separate PoE…
-
GS1900-8HP A.1 down after upgrade to 2.70(AAHI.5)C0
I have an old GS1900-8HP revision A.1 that was on firmware 2.60. After upgrade to 2.70(AAHI.5)C0 on the boot partition I lost access. I connected directly and got an address on VLAN.1 (should have been 10), which suggests it lost its configuration. I tried factory resetting and connecting to http://192.168.1.1, again…
-
GS1920-24hpv2 problem with VoIP/Vlan
Hello everyone, sorry for my English. I installed a gs1920-24hpv2 switch like this: Port 24 Data Trunk (VLAN 1) Port 23 Voice Trunk (VLAN 20) VLAN 1 Data, all ports, except 24, have been set untagged VLAN 20 Voice, all ports tagged except 24 and 23 I excluded port 23 from VLAN 1 and set it to untagged 20 Port 23 is…
-
GS1350-26HP Installation
Good morning, I purchased a GS1350-26HP to connect my POE cameras. I connected the switch to the NR7101 5G antenna but unfortunately I can't connect it to Nebula or connect to the web GUI. I also connected the switch directly to the PC, trying to connect to 192.168.1.1 but I can't find the page. I also changed the address…
-
problem
I have ZYXEL GS2210-24HP switch. After firmware update to and update rom and reboot: Messages: Bootbase Version: V1.00 | 12/18/2013 13:20:50 DRAM calibration...PASSED RAM: Size = 131072 Kbytes DRAM POST: Testing: 131072K OK DRAM Test SUCCESS ! ZyNOS Version: V4.50(AANE.4) | 07/08/2020 13:42:42 Press any key to enter debug…
-
GS1200-5 trunk port
Looking into this product and i was wondering how do i create a trunk port to the router and vlans assigned to each port? in more detail i would like to have eth1 to be trunk port and carry all vlans to my router, eth2-5 assigned to vlan20,30,40,50 respectively.
-
ugly bug in IPV6 config part of latest XMG1915-10E switch firmware?
2 new XMG1915-10E, both with latest V4.80(ACGO.1) firmware, configured standalone: (IP, DNS et al via DHCP and DHCPV6 active on VLAN 1, just one VLAN with ID 1) on both, almost always when I try to ask for details of the IPV6 status of vlan 1 (System - IPV6 - IPV6 Status - click on the only VLAN with index 1) the switch…
