-
GS3700-24HP PoE issue
Since some days poe fail to power the devices connected. There are 2 PSU rendundant but no log shows issues or anomalies. In attached diagnostic file Any idea to solve it?
-
GS1900 - separate 2 ports from the rest (aka splitting a physical switch into 2 logical ones)
Hi, I have a GS190024HPv2 switch in a simple configuration - not using any VLANs and using it as a plain switch with PoE turned on some ports. I have an optical-to-metallic media converter from my ISP which I'd like to power via PoE from the GS1900v2. However, I'd like to separate the signal from the ISP (WAN traffic) from…
-
Trunking port on GS1200-5/GS1200-8?
I want to connect a GS1900-24E to GS1200-5 and GS1200-8. Each of the later two could only be connected with one cable. I also want to have 2 VLANs on all three switches. As far as I understand the GS1900-24E has the ability to define trunking ports to connect other switches.I cannot find this in the GS1200 manual. Should I…
-
Packet latency on GS1900-8
Hello, Where can I find information about packet latency in GS1900-8 switch? I want to use it to control and get data from IoT devices and it's important parameter for me.
-
XGS1250-12 LAG 8x1G
Dear Team, I would need to get at least a LAG of 8 x 1G in order to make my flow go through my FW (10 ports x 1G on my FW) and follow the below diagram. Is it possible with the model XGS1250-12 ? If not, could it be in a firmware roadmap ? Or would you have another model to suggest ? Regard
-
GS1920-24: VLAN access to internet gateway?
Hi, I have a GS1920-24 Switch with Firmware V4.70(ABMH.6). My plans are to setup a separate Guest-Wifi that is located on a VLAN that can only access the internet and nothing more. Until now several problems occured but I want to start with the very first. How do I setup a default gateway (the ISP's modem/router) that is…
-
PoE problem
Hello! I have a problem with GS1900-24HPv2 switch, consist on "PoE Init Fail". Wich steps need to follow? Thank you
-
GS-105S v2 Just bought it and it dont work
GS-105S v2. just bought it, and connected it to computer, cant find ip to the switch configuration, no reset button. and cant even register the product becuase im missing the MAC adress.. and no info about how to set this up, plug and play clearly DONT WORK!!!
-
MS Visio stencil for Zyxel product required
from where can I download Microsoft visio stencil for complete zyxel products? I want particularly required Zyxel XGS4600-32F at the moment
-
how to configure ports if access points connected to switch and switch has different VLANS
switch has different vlans and need to tag vlans to different SSID
-
Turn off QOS on switch GS-108S v2
Hello, how do I turn off QOS on the GS-108S v2 switch? It has designated priority ports labelled on the back but I want them to all equal.
-
GS1100 - LED colors
What means the different color of the leds? I see green and orange.
-
Zyxel GS1920 series : how to config native vlan
Hi all, I am newbie for Zyxel swicth. I have just buy 05 switch Zyxel GS1920-24HPv2. on old cisco switch, i have configure command : Switch mode trunk Switch trunk native vlan x So please help guide me how to configre it on Zyxel 1920-24HPv2 ? Thank you so much ! Khainv
-
IP conflict with GS1100-16
Hi I am struggling with the set-up of a small office network. I have no technical background, which is why I chose the GS1100 to begin with 😅 The network looks like this ISP modem > Patch panel > GS1100 > mesh wifi > device My ISP tells me everything is fine with their connection and the modem. But the GS1100 is causing an…
-
GS1100-24 slow speed for devices with speed 2.5Gbps
Hello, I want to ask why the switch switches to 100Mbps and not to 1Gbps after connecting a device with a speed of 2.5Gbps?
-
Confused on VLAN setup
I'm trying to setup VLANS on this switch. But I can't see to get anything I assign a VLAN to grab a DHCP ip from pfsense. I'm probally doing something wrong in the WebUI of the switch. I have the switch connected on Port 12 SFP into the pfsense box. Switch: Pfsense VLAN: Pfsense Interfaces: Right now I'm able to connect as…
-
Link Aggregation funktioniert nicht
Hallo ich bin neu hier im Forum und hätte gleich mal ein Problem. Wäre schön wenn mir jemand helfen könnte. Folgend Konfiguration USG Flex und zwei 1900-24E VLan 1, 10,20,30,40 Es funktioniert alles die Vlans die Adressen Zuweisung alles prima. Nun wollte ich auf den Switchen auf den Port 1 und 2 ein LAG einrichten und bin…
-
LAG Einrichten
Ich habe folgendes Problem ich betreibe zwei 1900-24E hinter einer USG Flex. Soweit so gut es funktioniert soweit alles VLANS sind eingerichtet und zugewiesen. Auf den Switchen sind die Ports 1und 4 den VLAN 1untagged und 4 weitere getaggt zugewiesen. Die Restlichen Ports sind ebenfalls den entsprechenden VLANS zugewiesen…
-
XGS1210-10 reboot loop with 2x1GBit load balancing + 2.5G port used
Whenever I activate any kind of load-balancing on my Synology NAS with 2x1GB (adaptive without switch support oder static link aggreagtion with switch port) and plug my PC with 2.5G NIC in any of the 2.5G ports the switch will enter an indefinite boot-loop. If only 1G ports are used, everything works even with load…
-
XS1930-12F 10G Uplink Problem
I am new to using Zyxel switches. So, I am hoping someone can help me with this. Maybe I have a setting wrong, but I can use a 1G SFP optic and get the switch to link at 1G, but the whole reason I got this switch was to be able to uplink it at 10G for endpoint use. I have tried different SFPs and ports and can not get it…