-
Switch firmware release-note should mention browser requirement
Requirements for vlient OS and browser for management should be unecessary, but is obviously isn't. I just tried upgrade of a GS1200-5HP v2 switch which then got stuck in "upgrade-mode". Upload of firmware resultet in the error message "Firmware upgrade was failed". I tried 3 different firmware-versions available from the…
-
GS1200-8 Benutzeroberfläche nicht aufrufbar
-
GS1350-6HP-Garage A message could not be handled because it failed to be parsed correctly. Cloud N
I keep this message in the event log and I don't know what to make of it. this switch also drops off line every once in a while making it somewhat unreliable. Now in full disclosure I had to use a PLA6456 to get the network to this garage since trenching for a fiber line wasn't an option and point to point wifi would be a…
-
GS1900-24 - Unable to split switch into 2 different ip ranges, is this possible?
Hi, I asked about this some time ago but cannot find the original thread, nothing I could do would make it work as I would always lose communicaton with the webui and have to reset. I tried again for 6 hours last night with the same results and am once again back using to tplink switches for each ip range. Can someone…
-
xgs2210-52 inter-vlan routing troubleshooting
Dear all, We've configured a stack of xgs2210-52 switches but are running into issues routing traffic between vlans. The environment consists of 2 xgs2210-52 and 2 fortigate 70f connected in full mesh HA fashion, so the switches are stacked and both have a aggregated connection to both firewalls. But we're already running…
-
Can't import self-signed certificate to GS1920-24V2 (FW 4.80, ABMH.0)
Hi, I have a problem to import a self-signed certificate to my switch. I've tried it with a self-signed PKCS#12 file generated from opnsense. File extension is .p12. Then I've tried it with a compiled version from openssl under windows with bothe extensions .p12 or .pfx with and without a password. Whenever I want to…
-
Layer 3 lite XGS1930 series
The difference of Layer 3 Lite is only L3 lite = L2 + static routing ?
-
Technical Specifications
Hi All, I would like to raise some questions regarding the appropriate model of zyxel switch capable to serve the following requirements: Q1. Capable/Supports SNMPv1, SNMPv2 or higher. Q2. Shall be able to accommodate, integrate and provide general traffic handling and management services for at least four (4) different…
-
ZyXEL GS2200-24
How can i reset the switch to default password? and where can i download the firmware for this switch?
-
I need to upgrade the firmware on a Zyxel GS1920-24 switch to version 4.50
I need to upgrade the firmware on a Zyxel GS1920-24 switch to version 4.50. Thanks.
-
Fail over without NAT
So someone said about this for a switch and I said there is no WAN fail over but then something happened to me my ISP went down I had a backup but this did not work due to my PC getting the WAN over a USG bridge and when the internet went down ARP to the WAN gateway still happened so that the NIC still used the my main…
-
request for GS2200-8HP firmware
DEAR ZYXEL i am an engineer from indian railways. i have many these switches in our surveillance system. some switches are not able to bootup due to corrupted firmware. plz provide me firmware files. thnx in anticipation.
-
Latest FW for GS1920-8HP - and where can I find FW support?
What is the latest FW for GS1920-8HP. I am running V4.70(ABKZ.6). And where can I find FW support on zyxel.com?
-
XS3800-28
I used 2 XS3800-28 switches for stacking. Switches have 28 ports, of which 21-28 are combo ports. When stacking, 2 pairs of comboports (25-26, 27-28) become unavailable. Is this normal behavior? How to properly stack on a ring topology: 1) SW1 port 28 - SW2 port 27 SW1 port 27 - SW2 port 27; or 2) SW1 port 28 - SW2 port 28…
-
XGS1250-12 - ability to configure webpage logout time
When configuring either of my Zyxel switches (I have three XGA1250-12), sometimes the page timeout is too short especially when working between the three units and other IT systems and reverting back to a locked page. There seems to be a default of 5-minutes which can be limiting, unproductive and frustrating to use. I'd…
-
SFP+ not connecting to switch GTEK
So bought a XGS1210-12 10gb (inc 2.5gb) switch. Plugged it in to GTEK 10G SFP+ multimode transceivers and nothing. They say they support Zyxel (call out SFP 10G-SR on amazon). Any ideas? All other RJ45 ports work fine but SFP does not get recognised. Also I am a Mac user (sorry have PC buy work so not admin). I cannot log…
-
dhcp offer zyxel xgs-4526
greetings after creating a vlan, enabling a trunk port and enabling dhcp service on a zyxel xgs-4526 switch and establishing the connection with a gs1910 switch via the trunk, the pc connected to a port in access mode on the switch gs1910 not receiving dhcp offer
-
Import HTTPS certificate to Zyxel 1930-10 to avoid ssl error.
Good afternoon. I am trying to install an SSL certificate on my Zyxel switch. As much as I hit the "Import" button within: Maintenance--certificates, it gives error. I generate the self-signed certificate with PFsense in PCKS12 format as indicated in the switch, but nothing happens, it does not work. How can I import a…
-
GS2200-24P Firmware
Requesting latest to be ever released GS2200-24P Firmware.
-
IGMP Snooping and XGS1930-28, XGS1930-28HP, XS1930-10
I have three Zyxel switches, all working in Nebula cloud mode. XGS1930-28HP for my POE devices, XGS1930-28 for the rest devices and XS1930-10 for the high speed (above 1g) devices. I want to enable IGMP snooping since I am using some multicast traffic in my network. The only option I see in Nebula is IGMP snooping enable.…
