-
wi-fi does not give maximum
Hello, clarify one question about the maximum speed of wi-fi. I have a 100mbit tariff, but by wi-fi I get a maximum of 30mbits on the Internet they write that the speed will be limited by the device that receives the signal. I have a vacuum cleaner that has a weak filling. maybe it's in it? or am I misunderstanding?
-
XMG3927, static IPv6
I have a static IPv6 range and I want to configure my XMG3927 to use it... but, I've no idea how to do that... my problem is, that while I can set a static IP on my VDSL/PPPoE interface, I cannot set it on the LAN interface and... I cannot ping my modem via IPv6 from my LAN... so... to me it seems, that the configuration…
-
What are the main differences between GS-105B and GS-105S Gigabit switch?
I have looked at those two specs and could not figure out the differences between both of them. I can only find out that one is "Media Switch" another is "Unmanaged Switch". Someone, please explain it to me.
-
Is the Zyxel VMG3925-B10C provided by my ISP different from the consumer model?
Hi I am unable to set up more than one USB share on my VMG3925-B10C provided by PO broadband in the UK, i.e. it will only allow me to create a single share. If I try to set up a second share I get the eror message:Set SAMBA DIR Object Fail. I am also unable to update the firmware on this router. Thanks David
-
No new Network name in Network List in my SSL VPN connection
Hallo everyone! I have build and use a SSL VPN connection. It works, and all thing are ok, but one problem: I need to grant access not to all my subnet network, but only for a part of my subnet. I have created a new network object with a range of ip addresses that i want to share, but this network name is not visible in…
-
Unstable connection
Hej. I have change the internet provider and now with the new router my son's tablet lost connection and then connect again, I don't know what to do. The technician told me that he will give me a dinamic IP and that will work but it doesn't work, I have reseted both tablet and router, I have check which channels are more…
-
PPP LCP Down. Reason:0 lower down
Hi all on my VMG1312-B10A I have untimely disconnections... someone can tell what means "PPP LCP Down. Reason:0 lower down" ? thanks
-
IPV6 VMG1312-B10D
Hi I have been trying to set up IPV6 on my VMG1312-B10D.It seems to be working and i have followed the guide from my ISP, although its not quite the same, the wan setup page has no option "Prefix Delegation " https://support.zen.co.uk/kb/Knowledgebase/ZyXEL-VMG1312-VMG8924-IPv6-Setup My VMG1312-B10D is getting the correct…
-
[Zyxel VMG1312-B10D] How to recall access to a device that was connected to the router via WPS?
When I
first installed my Zyxel VMG1312-B10D home router, the WPS option was enabled
by default (path: Network Setting > Wireless > WPS). As a
result, a user that had physical access to the router managed to connect his
smartphone by using the WPS method. Since then, I set the WPS option to “Disable”,
in an attempt to…
-
NO DSL OR INTERNET YET WIFI SIGINAL APPEARS Zyxel-VDSL Gateway VMG1312-B10D
I have an issue where i have a wifi connection for the internet yet on the router both internet and dsl are both not working i am using my data to go online and this is an issue we had someone come over an install an open reach c5 master socket after using sky Q broadband and before this the internet connection was red but…
-
VMG1312-B10D upgrade to 5.13
Hi, I was using a 5.11 version of the firmware of this device and was using dslstats to get the connection data via xdslctl info --stats via telnet. Since the upgrade i have noticed this has stopped working and when i telnet instead of busybox i am now greeted with ZySh> and a very limited commands. Is there any way to get…
-
zyxel vmg1312-b10d not connect to internet after firmware update
I updated my zyxel vmg1312-b10d to the newest firmware version 5.13(AAXA.10)C0 and after that it cannot connect to internet. My settings are correct and the DSL light stady green but internet is red. My provider said to me that I shouldn't upgrade firmware. Any suggestions? #SP_Mar_2020
-
VMG1312-B10D firmware 5.13 AAXA.10C0 doesn't show LAN device icons.
Hi @Zyxel_Support_CPE and everyone, I upgraded my VMG1312-B10D today from 5.11AAXA.4C0 to 5.13AAXA.10C0 and it seems to be working well. However, I can no longer see icons of the all the LAN and WiFi connected devices. It just shows an empty page, see below. I know that there are devices working on the LAN and WiFi because…
-
Parental Control- "One connect setup"
Hi just got a XMG3927-B50A router and I'm trying to setup parental control where I need to untick the "one connect setup" box but the box is grey and I can't untick!!! I also notice that that are other box grey and I cant change such as the "Keep 2.4G and 5G the same" in wireless. Thanks in advance.
-
VMG1312-b10d firmware upgrade error
During the VMG1312-b10d firmware upgrade I'm facing the following error: My actual firmware version is: V5.13(AAXA.7)C0 Newest version: 5.13(AAXA.8)C0 Could you help me? #CPE_Mar_2019
-
Service after Warranty
Does Zyxel company service there unites after warranty time?
-
XMG3927-B50A - Disabled Checkbox for "Keep 2.4G and 5G the same" in WiFi settings
Hello I have recently acquired a XMG3927-B50A router and configured it via the wizard. During the wizard, I was asked if I wanted to combine the 2.4GHZ and the 5GHZ wireless networks, which I confirmed. Now I want to split them up again, but on the wireless settings page the checkbox to unpair the two networks is greyed…
-
VMG8825-B50B supported LTE dongle
Hi support, I have a VMG8825-B50B ( Firmware 5.13(ABNY.2)C0 ) I'm searching about a compatible LTE usb dongle to use as backup in case VSDL connection is not available. I found on site a very old compatible list where there is only 3G dongle. Please can you give me a new list with LTE dongle? Regards Antonio M.
-
EMG3425-Q10A
What is the maximum cable length that the LAN ports can drive?
-
Why is my 2.4G bandwidth only 20 mhz
I don’t see any place where I can set the bandwidth and channel. My current 2.4G connection rate is only 144 Mbps
