-
Setup switch spanning VLAN with XGS1930 series
Hello, I would like to use a fibre connection between two XGS1930 switches to transport two logical networks separated by VLAN: Or described in other words: All data on port 24 of the left switch (1) belong to VLAN2 (switch should tag them accordingly). All other ports (except SFP+ port 28) belong to VLAN1 (default…
-
Switch POE down.
I am using ZyXEL Gs1920-24HP to supply power for the access point. However today, the switch cannot supply PoE, but connecting to the computer is OK. Does it mean the switch is failing or what should I check? When I adjust the PoE status, the below error appears: Error: set PoE Management Extend Configuration fail!
-
Do I need a VLAN for IPTV (Magenta TV + Zyxel GS1920-24HPv2)?
Hello, I use IPTV from Telekom Germany connected to Zyxel GS1920-24HPv2. My question is: Do I need a VLAN for the Meda Receiver, to protect the LAN/WLAN from Multicast flooding? If yes, can anybody provide me a tutorial/guide to do this? Thanks in advance!
-
XGS1250-12 LACP & RSTP Support
Hi, just received my XGS1250-12 devices and found out that LACP & RSTP support is surprisingly lacking. Are there plans to add support for LACP and Rapid Spanning Tree Protocol (RSTP)? I also have a GS1900-8 which supports both. Thanks & best.
-
GS1200-8 vs. VLANs (OPNsense)
Hi everyone, I am fighting with VLAN setup on GS-1200-8 switch. My setup is OPNsense router with VLANs defined and I would like to use GS-1200-8 port 1 as uplink from that router with all VLANs so I setup all VLANs in switch config as tagged on port 1 (including VLAN 1). I would like to use rest of the ports to be a…
-
VLAN GS1900-48 VLAN
Hi, I have UniFi switches for all my main network but i have a issue adding the CCTV Lan to my Zyxel. Port 48 is a trunk port and my CCTV and lan is carried from my UniFi switch over to port 48 I would like port5 on the Zyxel as for my CCTV vlan only. Port 5 is untagged and port 48 is tagged for VLAN4 and 48 is a trunk…
-
XGS1210-12 switches with Ubiquiti Access Points and Controller
I am trying to replace my current 1GBps HP switch with two XGS1210-12 switches for 2.5GBe connectivity. Apart from the LAG issue for 10GB SFP ports (Which hopefully sounds like there might be a fix), I've now discovered a real problem with my Unifi devices. I have a Unifi local controller, with 5 Access points; 3 AC-HD, an…
-
GS2210-24HP Firmware Update
hi, i try to upgrade GS2210-24HP firmware from 4.1 to 4.5, but it show question mark on zon utility. and i also try to install firmware one by one, however the offical website hyperlink cannot be download. pls help.
-
XGS1910-24 Firmware
Can someone maybe provide a copy of firmware version 1.00(AABW.2) for XGS1910-24? I found the latest 2.00 firmware on the EOL list: https://webservice.zyxel.com/end-of-life But according to the release notes I first have to upgrade to version 1.00(AABW.2) which does not seem to be publicly available anywhere on the…
-
XGS1210-12 Link aggregation with Synology DX-513
I picked up the XGS1210-12 as I liked the specs - the 2.5GbE ports, plus the SFP+ sockets and, (most importantly), the option of link aggregation in the latest firmware. I connected things up and booted my Synology with it connected to ports 1-4 on the XGS. I've tried to get link aggregation configured to give me more than…
-
Do any of the MODERATORS actually verify and approve posts by new users?
I have a detailed question which I edited and is awaiting approval... can someone take a look please?
-
XGS1210-12 - Which 10G SFP+ Copper Module ?
Hi! I am wondering if anyone could recommend a suitable 10G SFP+ Copper Module for the XGS1210-12 Switch ? When I am looking for modules I see they are certified for certain brands... Which ones would work with the XGS1210-12 ? Thanks in Advance ! Best Regards From Martin Brandt.
-
log messages
I have a Zyxel GS 2210-HP switch and I have Dlink DAP-2610 antennas connected to that switch. A few days ago the antennas are restarting and the following log started to appear on the switch: 6432 Sep 06 15:38:53 NO system: PethPse Port 18 OnOff Trap, Port Detection Status is Disabledabled6434 Sep 06 15:38:53 NO system:…
-
GS1920-24HPv2 - Configuration due to "Saving Power"
Hello, is there any option for GS1920-24HPv2 to saving power? I have connect 4 Devices which uses the POE function.Is there any option or configuration for the switch to save energy?
-
xgs2210 I lost ip interface
HelloI have 2 xgs2210 switches in a stack.I don't know why but I lost the web interface.I connected to the console to assign it a new management address but I have errors (routing table)do you have a procedure? Best regards
-
GS1920-24HPv2: Disabling SNMP?
Hello, in my Homenetwork I am using a GS1920-24HPv2 Switch. My question is: How can I disabling the SNMP because I have note found any disabling/deactivating option in menu "Management -> Access Control -> SNMP ->..." The newest Firmware is running on this switch. Thank you for your answer!
-
Problem with switch RGS200-12P
Hello everyone, I try configure vlan on my switch, i delete native vlan, create our vlan with tag 99. Create IP interfaces with adress 192.168.99.110 then i create trunk port. Why i can't connect to web interface switch from another site (192.168.1.0/24) when i create second ip interfaces witch adress 192.168.1.163 and…
-
PoE issue at GS1900-24HPv1 - Firmware 2.70(AAHM.1)C0
Recently upgrade to firmware 2.70(AAHM.1)C0 on all of our GS1900-24HP switches and all are dropping POE power for no reason and log does not contain any errors. Tried to do a tech support download but switch just rebooted and POE power came back. Any one else have issue with this firmware? For now I have rolled back…
-
Mismatch in port numbering with snmp on GS1920
Hi everybody, I'm monitoring my switches (GS1920-24HP and 48HP) in Observium or in Switchmap but there's a mismatch in the port numbering.The numbering begins by "0", thus if port #5 is in vlan 200, it's shown that it's port #4 who is is that vlan in observium.Has anyone experienced this problem ? Any suggestions to fix it…
-
GS1900-8 change ip problems
Hi to all, I have purchased and GS1900-8 managed switch, but I can't configure a new IP address. Configuring the PC connected via cable on the same factory subnet 192.168.1.0/24 does not detect the device via ping, TCP or via web browser. I tried on all physical ports (1 to 8), also factory reset but with identical results…