-
Poe Functionality with Mikrotik Products
Hello, I have a switch ZyXEL GS1900-24EP-EU0101F and trying to use PoE ports to power up multiple Mikrotik devices (3x AP, 2x Routerboard, 1x Cube 60Ghz) and Mikrotik does not want to Power UP. Is this PoE working with Mikrotik products? Many thanks for any feedback or experience. Have a nice day.
-
Troubles with network - Layer 3 Routing
Hi, we're migrating from the "firewall" (which until now worked as a router) to the switch (XS1930-10), but after assigning a static IP address (from /27 public range assigned by datacenter), the switch is not visible from the outside or from the inside, and it's without internet connection - also of course the device…
-
XGS1930-52HP VLAN
I have 4 of these units and 1 is connected via an SPF + and the other ones are connected with a network cable. My VLAN 1 is working across all switches but my other VLANs are only working on the main switch. Main switch is assigning the VLAN DHCP & DNS correctly. I have trunk turned on on the upload feed of the sub…
-
VLANs and DHCP
I set up two VLANS on a GS1900-24, the first 16 ports on the 1st and the last 8 ports on the 2nd. Each VLAN has all member ports set to untagged and all others set to forbidden. I have two separate subnets that communicate via routers. What I was hoping is that the two VLANS would act like two separate switches, so I could…
-
GS1900 at over 70% memory usage. newest firmware, factory reset,no config or devices connected
Hello, i have bought a used GS1900-24, hard reset it and before even connecting any devices i notice it is sitting at over 70% memory usage. it had firmware from 2015-2016.So i downloaded the newest firmware and installed it. factory reset And it is still sitting at over 70% memory usage with no devices and no config. What…
-
Switch ES-2024 - Ports Limited to 100 MB/s
All the ports of my Ethernet Switch ES-2024 are limited to 100MB/s. Can I increase that rate?
-
SFP+ uplinkport on XGS1930-52HP switch
Can we connect our server with a SFP+ Nic with this port or is the port only for uplink.
-
VLANs not working
I have problems with my VLANs and I am battling to figure out what is wrong. I have 6 Zyxel Nebula enabled APs, connected to 6 Zyxel switches that all connect to a Ubiquiti 16 port fibre switch. VLAN DHCP is done by my Sophos firewall. I have 2 VLANs (100 - Guest Wifi, and 300 - Staff wifi for BYOD) and want to add some…
-
ZyXel GS1900-24 V2.70(AAHL.0) switch endless login redirect
Hi, I bought a GS1900-24 switch witch V2.70(AAHL.0) firmware. The switch worked for 2 days and when i tryed to log in a it is redirect me after 2 second to the login screen. The only solution is to unplug the power cable wait 2-3 sec and plug in back. After it is works again for 1-2 days, but after againt product same…
-
Problem with Tagged VLANs on GS1900-10HP Switch
I am having a problem with tagged VLANs between a Zyxel
GS1900-10HP switch and a Zyxel USG20W-VPN firewall/router. Appreciate any advice on how to resolve this. Hardware Information Zyxel USG20W-VPN, Firmware v5.30(AVAR.0) / 2022-04-20 / 2022-04-20 01:43:59 Zyxel GS1900-10HP, Firmware v2.70(AAZI.1) | 01/11/2022…
-
XGS1250-12 New Owner: Setup Questions re: LAG and Statistics
Hello, I just bought an XGS1250-12 and hooked it up to serve as my multigig switch in the back of my office, since I was running out of ports on my QNAP QSW-M2108-2C, and running stupidly long ethernet cables across my floor was getting a bit old, even if they were hidden behind furniture. ;) This is the first non-QNAP…
-
GS1900-8HP - A phantom firmware
During usual trip-check for upgrades and fixes, I stumbled upon unexpected scenario. My GS1900-8HP switch have 2.70 P0 firwmare. It's up since 230 days, needed a nice reboot "just in case of". And while rebooting, i found that the latest firmware available on support site is... 2.60 P4. :confused: What on earth happened?…
-
Bridge GS1920
Hello, I have a ZYXEL GS1920 which is placed behind a Fortinet SWITCH. How can I switch my ZYXEL to bridge mode? Thanks a lot.
-
404 error when trying to backup the config of GS1900-48
I have a GS1900-48 with the latest firmware which will not backup the configuration through the GUI. When you select the running-config and backup via HTTP it would normally prompt you to save the file, instead I get the error: -------------------------- 404 Not Found The requested URL /tmp/running-config.cfg was not found…
-
XGS1250-12 and VLAN tagging
Will the XGS1250-12 forward or drop an 802.1Q VLAN-tagged packet received on a port that is not a member of the VLAN identified by the tag?
-
GS1920-24HP console
I have a GS1920-24HP that apparently lost its firmware and is stuck with the sys light flashing. I have a 4 pin console cable as there is a 4 pin console port on the right hand side of the switch. Is there something specific that I need to do to get console access to the switch? I read elsewhere for the pinout of the port,…
-
GS1900 V2.70(AAHH.1) firmware
HiI notice the above FW was recently withdrawn from the downloads area. I cannot find any announcement as to why. I upgraded my switch to this firmware some time ago. Should I downgrade to 2.6?Many thanks.
-
Zyxel GS1910-24HP Reset .ROM Firmware
Hi, we have taken over some Zyxel GS1910-24HP switches which need resetting, I followed this tutorial online but need the .ROM software it seems to be able to reset it. I can't find it online if anyone can supply it? Thanks
-
GS2210 Classifier and Policy rules logic
I make the following: --------------- Classifier 1 MAC allow port 19 Source MAC
xx:xx:xx:xx:xx:xx --------------- Classifier 2 Block all
port 19 port 19 --------------- Classifier 3
DHCP_cast_port_19_allow port 19 Destination MAC
ff:ff:ff:ff:ff:ff Source port 68 Destination port 67 ----------------- Classifier…
-
Dynamic VLAN Assignment By MAC Address
Simple setup, VLAN aware router connecting WAN to multiple VLANs on a single managed switch, a Zyxel GS1900-24Right now, the config on the switch needs to know "assign this port to this vlan and incoming packets will be tagged or untagged". From an admin perpective, that is a pain, especially when different devices move…
