-
NWA90AX as a bridge to a cellphone acting as a WiFi hotspot
I've just bought a NWA90AX in the hope that I could set it up as a bridge from my Android cellphone acting as a WiFi Internet hotspot to my wired intranet (a role that's presently being filled by my laptop), but can't find a way to do it. The NWA90AX won't even detect other WiFi devices in the vicinity. Can it do what I…
-
NWA210AX | Capative Portal not working with L2 Isolation
Hi, I’m using Nebula managed NWA210AX together with XMG1950-10E Switches and an OPNsense Firewall. I want to host an open WiFi-Hotspot with Nebula Authentication and L2 Isolation. My problem is, that the capative portal is not working anymore when L2 Isolation is activated. MAC-Adresses of the Guestnetwork Interface and…
-
ZXHN H168A V2.0 Firmware
Hi I Use ZXHN H168A V2.0 . The modem is mine. I bought it but it is very restricted by ISP. I want normal software with no restrictions offered by Zyxel. This is my right. I searched a lot but couldn't find it.
-
Wireless Bridge Mode and NWA210AX LAN Port
Hi, In Wireless Bridge mode, the NWA210AX and its LAN port are Down often. I need to permanently connect a DVR Recorder via LAN port. Which configuration should I implement? Or, alternatively, which Hardware do you recommend me to use? My network consists of 2 x NWA50AX, 1 x NWA110AX and 1 x NWA210AX in MESH mode. NWA110AX…
-
How to install Linux driver?
Looking on I get the Linux driver as tar.gz. But there is no install script. How to install this driver? Thanks
-
password invalid
-
NWA130BE / BE11000 Power Supply
Hi, what are the exact requirements to the 12V power supply for the NWA130BE AP? What are the barrel jack dimensions (I'd guess it's 5.5mm / 2.1mm again?) What's the polarity of the jack? Is there a recommended power supply to use? Thank you!
-
Three NWA50AX - Wrong Pwd on one but roaming possible
In my setup I have three identical (?) configured NWA50AX, all three hanging on the same switch. I configured them without nebula, as I don't have any internet-connection to this system. I can login with mobile ios-devices on two of them, on the third one they are "blocked by key handshake fail" and saying wrong password.…
-
Does the NWA130BE support Zero-Wait DFS?
Hello everyone, Unfortunately I can't find any documentation about the support of Zero-Wait DFS for most access points. Only for the WAX650S I found the feature mentioned in these release notes. The feature is quite important though. Without it you are either bound to non-DFS bands or will have wifi disruptions due to…
-
NWA50AX POE injector with Smart-Mesh
Hi there I use a NWA50AX Pro in my garden, it is installed in the Zyxel Outdoor case (SKU 149000). I use the AP in Smart-Mesh mode, meaning the uplink is wireless from another Zyxel AP inside the house. I would like to power the AP in the garden via POE from a POE-Injector. question: Is it possible to power the AP from the…
-
NWA50AX Pro: where to set country code?
I'm optimizing some settings in a shared among several APs. After a DCS and a manual channel set, NWA50AX Pro greeted me with this warning. …. i was quite uninpressed, but whatever. I lookd around a lot and… i did not found any place to configure… country. Outside the wizard… this part come from page 54 of user manual,…
-
NXC2500 not accessible after failed upgrade
Hello, I tried to upgrade one of our NXC2500 controller from 5.x up to 6.10 from here:https://support.zyxel.eu/hc/de/articles/5741937172370 Unfortunately this link was may not a firmware upgrade instead a kind of a fix. The firmware upgrade failed and the SYS led was blinking red. After that the controller was not any more…
-
NWA50AX Pro: simultaneous WPA2-PSK and WPA3-PSK on the same SSID
As the topic title, I'm running firmware 6.65(ACGE.1) and I would like to know if i can setup both WPA2 and WPA3 on the same SSID at the same time.
-
NWA55AXE can't connect in WDS with nwa5123ni
I bought an nwa55axe to try to create a wds extension with a previously existing nwa5123ni, which is connected to a wired network. After following the guide linked below, what I am seeing is that the nwa5123ni, configured as ap root, shows the nwa55axe connected in wds, but with a signal strength of -95db, regardless of…
-
Ability to customize profile names after setup via Wizard
In response to the requirements raised by user @mMontana , we are considering changing the spec that allows customization of profile names after the initial setup using the Wizard as the SSID profile name, Security profile name, etc. This suggestion originated from the discussion found here: NWA50AX Pro: simultaneous…
-
Building a home network with multiple access points
Hi! I plan to upgrade my home network in the near future, but I wish to do it in 2 steps. I am interested in getting 2 of these APs - NWA130BE (BE11000). For me, it is a bit overkill, but pretty future-proof. They should be enough to cover a relatively big apartment. I wish to get those APs first and use them in my…
-
NWA110AX -- WLAN interrupts several times per day
Hi all, I am facing annoying issues with my NWA110AX AP. Those are already there since 1.5 years, but I ignored them successfully up to now. I now work a lot from home recently, and I just realized how bad the situation actually is. Not acceptable at all, I would say. Setup: NWA110AX connected to Zyxel GS1900-24EP (PoE)…
-
NXC2500 firmware update
Hello team, I was wondering if you can help me locate the updae file for my Zyxel device? Also, is it Okay to upgrade from V5.40 to the latest V6.10? In my WebUI, I can only upgrade to either the same V5.40 or a list of old and similar versions, should i choose one and follow the upgrade path maybe? Please do let us know.…
-
NWA50AX Pro: no SNMP referral into configuration section nor manual
I'm running firmware 6.65(ACGE.1) latest available at time of writing. AP has gone through wizard configuration. There's stated: no SNMP. That's disappointing, due to presence of SNMP on a stale product like NWA-1123v3, and the "Pro" naming. Same destin as "non pro version", which has been requested (by the way, I'd love…
-
Can't access my Mac via LAN from another computer by host name .local
I have a mac with local host name. Let's say MACBOOK-pro-Name.local. It pings fine from the MAC itself. I also have a static LAN ip Address on this MAC like 192.168.1.7 I need to connect to a webserver on my mac from a PC in the same LAN. But PC just cannot even ping the mac by its host name. To make sure it's not a router…
