-
extend my wifi coverage
Hello, I am a private user with little experience and modest skills. I have a NWA50AX PRO and I want to use it to extend my wifi coverage. Where I want to put it, I don't have a network cable yet to use it in AP mode. So, I thought that in the meantime, I would set it in repeater mode. But when I am on the page below, and…
-
how to enable or disable OFDMA for wifi6
hi can I enable or disable OFDMA for standalone mode or nebula ?
-
[Campaign] Adventure 2 is OPEN NOW!
The Great WiFi Expedition Greetings, case explorers! Following the excitement of our Switch adventure, we’re thrilled to announce Adventure 2: Uncover the WiFi Network Case is now open on your treasure map! Are you prepared to track down the elusive signals, unveil the secrets, and solve the mystery of networking errors…
-
Throughput when MLO is enabled
Hello, I’m currently testing the Zyxel WBE660S with MLO enabled using iPerf3, but the throughput is significantly lower than expected, reaching only about 350 Mbps. My test setup includes a PC connected to the access point via Ethernet and a Dell XPS (with MLO support) connected over Wi-Fi.
-
Zyxel NAP102 AP’s not switching to standalone mode after removing from Nebula
Dear forum users, I recently purchased two second-hand access points (Zyxel NAP102). These devices were previously registered in Nebula. Using the Zyxel Nebula app and the QR codes on the devices, I was able to register them in Nebula again, and everything works as expected. However, when I remove the APs from Nebula…
-
zquam
hello, somebody knows, where i could find ZQUAM cellular network amplification products in Italy? Thanks Telemaco
-
NWA130BE - Import custom certficate and key (Let's Encrypt)
Hi there, I tried several ways to import my custom certificate to my NWA130BE access points and I cannot seem to make it work. I would like to replace the default one by this certificate to remove the warning in Web Browsers. The FQDN and certificate are working fine everywhere else (Proxmox, Portainer, etc.). I have two…
-
SSID not working if profile name is not the same
Preamble: i found this behaviour on two different products. First device is a NWA50AX PRO with V7.00(2) firmware and 14:XX:XX:XX:XX:XX mac address. Second device is a NWA1100-NH with V2.12 firmware (still a wonderful AP… that have SNMP inside) I'm assuming that I have the "Mobile" SSID (actual newtork name) with the…
-
Unstable Wifi
hello all. We have placed a few months ago an complete new network at a customer. We only use zyxel devices, connected to nebula. We have issues with the wifi. Last week i was at the customer site, and i was connected to the wifi. One moment i had 80mbps up/down, the following moment i just had something beteween 0,8 and 3…
-
I cannot recover Wi Fi password by any standard methods
-
NWA50AX PRO cannot disable into wizard the first SSID. (firmware 7.00 P2)
Mint new NWA50AX PRO. Delivered firmware 6.55. On premises mode. Connect on the web interface (DHCP), follow the wizard, disabling the networks (I have a configuration that i need to upload, but it's made on a more recent firmware). Update firmware to 7.00 P2, reboot. Connect on the web interface , following the wizard,…
-
no MLO on 2.4GHz
I've noticed the following in my WBE660S logs: Interface: wlan-1-3 MLO disable, reason: Unsupported radio mode option.. I've also noticed that my WiFi 7 clients won't do MLO with the 2.4 GHz band, though it works great for 5 and 6 GHz. I assume from the message that some option I'm using on 2.4 GHz (but not on 5 or 6 GHz)…
-
Shelly Devices and Athom Homey
Hi! I have Flex100, GS1350-HP and two AP, NWA110AX and NWA5123AC-HD. I have two vlans and one SSID for each. Both Homey and Shelly devices are connected to the same SSID. My issue is that Homey and Shelly devices stop ”talking” with eachother. It works fine after a reboot but after a while they stop. I can access both…
-
NWA130BE 6GHz radio not working correctly
I have configured my NWA130BE with two SSIDs. One is for 2.4 and 5GHz only and one is for 2.4, 5 and 6GHz together. The 6GHz SSID is showing up for a few seconds before disappearing for a few seconds, then coming back, repeat indefinitely. My phone will only connect to the 2.4 and 5GHz bands, showing as WiFi 6 and not WiFi…
-
AP problem
Hello, I have 2 Zyxel switches and 3 nwa90ax APs in my system. I had a system that was working properly until yesterday. There was 1 SSID defined in the system. I added 2 more. Today, one of the APs started not working properly. When I removed it and moved it to another place, it works properly. But it does not work in its…
-
NWA 1123 AC-HD
Bonjour , je souhaiterai avoir des informations sur les configurations de ses routeurs . Un client m’a contacté afin de configurer ses 8 répéteurs wifi de cette référence . Elle souhaiterait changé le nom SSID et permettre la connexion d’un répéteur à un autre automatiquement avec son ordinateur / tablette et téléphone…
-
NWA130BE firmware update from 6.75p0 to 7.00p2 or p3 fails
I just bought an NWA130BE for testing and evaluation and, while the AP is now fully configured in local admin mode with no other oddities, I cannot get firmware to update from 6.75p0 to 7.00p2 or the newly released (as of October 21, 2024) p3. I've disabled ad and script blockers, turned off all extensions, switched…
-
FWA710 - This device is managed by Nebula ?
Hi Just picked up a FWA710 but I get an error code when trying to log in. It seems the device is managed by "Nebula" and I'm unable to use the username and password on the back on the device to sign in. Can this Nebula thing be removed? I would like to use the device as a stand alone device. FWA710 Serial number:…
-
Fate/Time on NWA-50
-
Wac6103d-i sudden stopped to support 5gz device
i tried to reset it but same issue it is not 5gz devices and it just supporting only 2.4gz devices
