-
Changing nat type?
i have this router EMG3525-T50B. my ps 5 shows nat type 3 but i want/need nat type 2. How can i change it?
-
How to have different 802.11 Mode on 2.4Ghz and 5Ghz - (EX3301-T0)
I just recently set up my new Zyxel EX3301-T0. My phone an different computers had no problem connecting after setting up the router, but an older Windows PC couldn't even find the SSID in the list (neither the primary nor the guest). After some troubleshooting I found that if I change the 802.11 Mode from "802.11b/g/n/ax…
-
AX1800 Wi-Fi 6 Router Does not Work
Hello, I bought AX1800 Wi-Fi 6 Router yesterday and I tried to use that. I connect the ethernet cable to WAN port, and adjust the wi-fi settings(password, name, etc) from 192.168.123.1 website. When I check from that website, internet connection seems fine but router keeps blinking red light and I can connect the internet.…
-
EMG3525-T50B block access to other LAN addresses ?
Hi. Home network user. I have a Zyxel EMG3525-T50B router connected to our fiber line. All of my fixed PCs at home have static IP addresses allocated by the router, based on their MAC addresses. One of the LAN ports connects to a Tenda router ( with cat5 cable ), which is used as an wifi access point for mobile phones in…
-
Slow wifi due to mismatched country codes?
Hello all! I have a self-assembled mesh system here, consisting of a NBG6604 (as access point and router), a NBG6503 (as access point) and two WAP3205v2. All devices are connected with Ethernet cables as backbone, have the same SSID, and use channels 1, 5, 9 and 13 (on 2.4 GHz). This configuration has worked without…
-
Lost access to my EMG2926 router dashboard during port forwarding
Good day all, Hoping some one can help. Recently I was trying to port forward so that my kid could host a personal blog / website on our Synology DS220+ NAS, located on our zyxel EMG2926 router at home. During the process, I accidentally rerouted access to the router dashboard (192.168.0.1) to the NAS (192.168.0.103), and…
-
Why does my EX3301-TO no have TR69 option?
Hi, As the title says, I dont have any option for tr69 under remote management. Thanks
-
zytel t50 remote management by default
hello, I experienced that my zytel T50 is resetting to factory settings even after simple reboots operation (not all the times but it is happening). This is of course disabling remote management settings (http/s acces via Wan) which I can’t set back when I’m abroad because the adim interface is not accessible anymore. Did…
-
Remotely configure network access for Zyxel EX3301-T0
I have a Zyxel EX3301-T0, and would like to be able to control network access on it (for a predefined set of devices) from Home Assistant. In other words, I would like to remotely change settings under Security -> Mac Filter or Security -> Scheduler Rule. I've looked at SNMP (preferable) and ZySH through SSH, but is unable…
-
C1100Z: How to disable AP Isolation
With the Zyxel C1100Z using firmware: CZW007-4.16.012.15, wireless devices can not talk to each other. It makes it impossible for a cell phone on the network to monitor a camera on the same network. How can I disable WiFi AP Isolation for none guest devices?
-
Finding password for WAP 6804 that was reset by NOC?
Our NOC tested and reset the Wap 6804 that i used, and apparently the original stickers were gone or damaged, because the only stickers on the WAP are a serial number and MAC sticker that looks like it was just printed on a home printer. I have this installed at a customer that is way out in the country, and am trying to…
-
Firmware Upgrade EMG3525-T50B
Please advise where I can upgrade firmware for EMG3525-T50B
-
VMG3925 B10C Cellular Backup problem
Prior to lockdown I was supplied with a VMG3925 B10C by my ISP. It became the centre of my little network getting internet access through ADSL. Since lockdown ended, I travel much more, but only need to use my home network for a couple of months at a time; an ADSL connection does not look viable. I am hoping to use a 4G…
-
Power up VMG3625-T20A did not provide Internet access
Today powering up my VMG3625-T20A router did not provide Internet access. See attached system log extract lines 107-44. I then performed a Reboot from the Maintenance section and the Internet access was established. See system log extract lines 43-1 (ZyxelLog_10042023.pdf). The router was powered off in the afternoon of…
-
Parental Control Profiles
How many Parental Control Profiles can you make on a XMG3927-B50A is it 12 as Its not letting me make another (13)
-
how disable WPS in VMG3625-T50B
i have VMG3625-T50B and updated Firmware to V5.50(ABPM.7.3)C0 and after instal this update cant disable WPS. now how can be disable WPS?
-
Zyxel P-791R v3
I have Zyxel P-791R v3. (sn S182S48000015) It is not worked. How i can burn\change firmware on this router. Can you send\give me a firmware and instructions for this model? my email: egor.dev@izhservice.ru
-
Router DX5301-B2 - USB file sharing acros SMB v2/3
I have this router from the B4RN ISP. I am trying to set up file sharing for video files on an USB connected SSD drive connected to the router. I can see the folders on the USB and have set up sharing on the router GUI. Is the OS of the router Linux?Should it connect via SMB v2 or v3, or is it accessible using another…
-
dnsmasq 'local' domain configuration [XMG3927-B50A]
Hi, If there is a plan to release a firmware update for the XMG3927-B50A at some point in the future (please do :) ), could I request the addition of the 'local' config option to dnsmasq? This should inform dnsmasq that the domain set in 'Maintenance > System' is local and it may answer queries from the hosts file or DHCP,…
-
MTU on IPv6 over IPv4 tunnel [XMG3927-B50A]
Hi, After enabling '6RD', i.e. an IPv6 over IPv4 tunnel, basic IPv6 connectivity works, but I'm experiencing significant timeouts with a subset of sites. This is perhaps best illustrated by a large number of failures in the 'Other IPv6 Sites' tab on https://test-ipv6.com/ I initially suspected a problem with Path MTU…