-
Moving AP to NEW ORGANIZATION
I have removed a device from the Organization/Site but I can't add it to another site. 2021-09-25 22:28:31Removed device: 5C:6A:80:xx:xx:xx / S172VxxxxxxxxInventoryStewart Ives When I try to ADD DEVICE under the new organization I continually get this error: Device is already registered by another user. Add the device by…
-
Why is NSG100 LAN1 DHCP limited to 32 IP addr ???
I have a big site with 8 switches and 30 APs. The NSG100 Nebula Security Gateway does not offer IP addr to all network equipments, even if i extend the DHCP address range to 60. Is there a limit on the number of devices per site that an NSG100 can handle ?
-
Streamlining process for purchasing licenses and upgrading your Nebula organization in NCC
In Nebula P12, we’ve made a significant improvement to
the license purchasing progress; users now are able to use the calculator to estimate
how many licenses he/she needs and exports the purchasing list. Also, Nebula
Control Center (NCC) are linked to Zyxel’s online store – Marketplace now, users
are able to buy the…
-
USG Flex 700 @ 1Gbps
I have the above on a FTTP 1 Gbps internet connection but can only get around 520Mbps with UTM enabled. Speed rises to around 700Mbps with all security disabled but this appliance is rated @ 1350Mbps so something is wrong. Anti-Malware is in Express mode!
-
Nebula Device status On but cannot reboot and SDWAN lost connection
Dear Sir / Madam, I have one Nebula Device status On but cannot reboot and SDWAN lost connection, yesterday connection is normal, please advise me. Thank you.
-
roteador emg1702-t10a IPV6 não funciona a partir das versões 6.47 do mikrotik
olá, vários meses já enfrentando este problema com o roteador zyxel emg1702-t10a, ipv6 não funciona de forma alguma, já tentei contato com o suporte do brasil, porém sem sucesso, a resposta que tiver foi que o pessoal de Taiwan estariam muito mais ocupado com coisas mais urgente e não se dedicaria na resolução do problema.…
-
Move AP NWA1123-ACv2 to another account
i want to move 4 APs to a new account, i removed them from the organization, but i'm still not able to add them to a new account. There is always the message, that the device is added by another user, pls hlp, thank you.
-
VLAN help GS1920
Network setup inherited from previous employee(s). Two geographically separated locations conntected via two Sophos XG firewalls with VPN. The VPN is deemed healthy by Sophos support and the VPN connection itself is as stable as it gets. Mostly everything seems to be working just fine except it seems the vlan-setup on the…
-
AP offline on Nebula
Hi, We’d like to use Nebula cloud for
management because I knew the benefit such as APP and wireless health auto
optimization features. We’re facing an issue that we’ve registered
and added the AP into the site via nebula APP, but the AP keeps showing offline
on NCC and its LED flashing in Yellow/Green status after…
-
535 authentication credentials invalid
In nebula, I was assigning my new fifth VPN100 to one site (the device was activated). When saving it the message "535 authentication credentials invalid" was shown. No ZTP sent to me thru email.This did not happen before.
-
How could I setup more Access Points than Switch Ports
Hey, we need to deploy more PoE APs on a remote site. There are several floors that need to get APs but also have APs underneath them. There are thick concrete walls and floors between them so the connection just isn't good enough in the top floors. So before I go out and buy a bigger switch and more Access Points, I just…
-
Setting USG FLEX 100
Buongiorno. Espongo alla vs. cortese attenzione ed esperienza, quanto segue: Linea TIM 1 Gbps,notebook collegato direttamente alle porte del router TIM Hub, velocità media rilevata = 850 Mbps. Collegato il router al firewall Zyxel USG FLEX 100, notebook collegato direttamente alle porte del firewall Zyxel USG FLEX 100,…
-
Upgrading Flex200 to Flex500
Hello, If I remove a USG FLEX200 from a site and register a new FLEX500 instead (to upgrade speed) will Nebula push the proper configuration to the device? Will I need to make any changes?
-
Switch ownership
We're switching IT support companies and need to switch ownership of the account. We're using the free version of Nebula. How can I do that?
-
How can we enforce MFA on Nebula admin accounts
For security reasons we want to make sure that all admins in our Nebula organization use MFA. Is it possible to get an overview of admins who have/haven't enabled MFA, and is it possible to enforce the use of MFA on all admins? (Menu Organization-wide -> Configure -> Administrators)
-
Deregister an AP completely
I thought that I had deregistered some AP but at the time of reregistering them in another organization. It tells me that they are used by another user. Could you help me
-
AP management VLAN vs switch settings
It's quick and easy to assign a management VLAN ID for the Nebula switches, but it seems to be different for the AP's. Is setting the LAN1 port PVID the only way to do it? That seems like it would cause some issues for the default VLAN.
-
NAP 203 not connecting to internet
I have a NAP 203 that was working fine last night but will not connect to the internet now. Tried managing it under my profile but cannot connect to it. What do I do?
-
Is There A Way To Get Switch Port Information Of AP When It WAS Online
AP is currently down. When last time it online, we can see the neighbor info and switch port information. Now it offline, we cannot see the switch port it is connected to. How to check where the AP connected to when it WAS online?
-
zyxel VPN nebula device and SD WAN down and nebula website load slowly
Dear Sir / Madam, We checked nebula website load slowly, besides zyxel VPN nebula device and SD WAN down, please advise us. Thank you.
