-
NAS542 services turning off
Hi, I have a NAS542, and I want to use it remote. I've done the setup for myZyXELcloud, and everything works fine, for 2-3 days—after that all the services turns off by themselves (WebDAV, FTP, etc.). It keeps repeating if I turn them ON. Do you know what could it be ?
-
Fix slow speed with NAS326 and NFS
Hi, I activated NFS on NAS326 and I'm directly connected to my NAS. Then I start to save files and speed is up to 150 MB/s, then it decrease rapidely less than 10MB/s... When I'm connected with gateway (Freebox Crystal) speed start up to 100MB/s then decrease rapidely less than 2 MB/s...My Ethernet controller is Realtek…
-
Can I install NAS326 Firmware on NAS325?
Is there any way to update my NAS 325 firmware to NAS 326? or is there any new and compatible firmware for NAS325 with features of NAS326?
-
NAS326 V5.21(AAZF.11)
Hello, since the new Firmware the mysql Service is not starting anymore: Enable package "PHP-MySQL-phpMyAdmin" failed.Does anyone has an idea?
-
NSA325v2 Multi HDD problems?
Have a NSA325v2 running v4.81 fw and 2 HDD's * WD Red 2.0TB - WD20EFRX (12VDC: 0.45A) * WD Red 4.0TB - WD40EFAX (12VDC: 0.28A) if i use only 1 HDD at a time, both work no problem, either bay inserting both at the same time, only the 2tb spins up when powering on tried hotswapping the disk and the other disk LED goes red,…
-
NAS540 SQL Server startet nicht
Hallo, hier werkelt ein NAS540 auf welches leider die neue Firmware V5.21(AATB.8) aufgespielt wurde. Seitdem lässt sich der MySQL Server nicht mehr starten. De/aktivieren bringt nichts, ebenso wenig die Deinstallation und Neuinstallation des Paketes. Hat irgendwer noch dieses Problem und eine Lösung parat? Danke und Gruß C.
-
ownCloud NAS542
Hello everyone!I installed the ownCloud and php-mysql-phpmyadmin packages. But both packages are disabled. My attempts to enable these packages were unsuccessful.Do you have any ideas?Thank you in advance.P.S.: the latest firmware version is inside
-
NAS326 Print server after update to V5.21(AAZF.11)C0
My NAS326 was updated to the latest firmware (V5.21(AAZF.11)C0), now I can´t use the print server. I saw in the change log that CUPS was removed. How can I re-enable the print server?
-
Move data from NSA325v2 to NAS542
Hello I bought a new nas drive as my old one is falling apart. I would like to transfer the data from my old nas to my new one without having to do it through windows explore as it takes ages. Could someone advise on the best way to do this? Thanks
-
Nas326 Twonky Server broken after firmware update.
So my Twonky server no longer works. It's on, but the web address no longer works. And my Smart TVs show no files being shared. It worked perfectly before the firmware update (5.21.10), there appears to be no way to rollback the firmware. Nothing else on my system has changed. Can it be fixed, or do I throw my NAS326 away…
-
NAS540 Still Repairing after 72 hours
I had a drive fail on raid 5 configuration. I replaced the failed drive and started the repair process. After the resync progress it is now at "repairing" for 15 hours. Looking at dmesg and mdadm --detail; it looks like it finished.Is there any other step to complete the process or did it finish and the UI is bugged out?
-
Nas 542
On My Nas 542 When trying to add DyDNS setting On Status Getting A Fatal Error And Disabled I,m Using DUC app with all green on it so do not know why this keeps happening
-
NAS540 V5.21(AATB.8)C0 inaccessible after reboot problem
Hello,I updated my NAS540 from the version V5.21(AATB.7)C0 to version V5.21(AATB.8)C0.After that, I am unable to access the NAS after I reboot it from the webgui. This is a random problem. Sometimes I can access it after a reboot and sometimes I can't. I tried with DHCP and fixed IP, same problem! After it becomes…
-
NAS326 new firmware V5.21 (AAZF.11)C0 - UPnP
Since I have installed the new firmware V5.21 (AAZF.11)C0 the NAS326 is unable to find any UPnP supported routers. (router UpnP is active). I know that it is possible via port mapping (router) but sometimes I need myzyxelcloud to update UPnP on a remote nas/router. Any idea?
-
NAS 540 failure
I have a NAS540 w 4 hitachi 4t drives. It was configured raid 10. It fails to boot with all 4 drives. If I pull out drive 4 it does boot but the the interface says drive 1 is bad. If I reboot it it will sometimes try to rebuild the volume. But after rebuilding it will work for a while then fail. Then I will need to pull…
-
NSA325 with Windows 10
My NSA325 has become hard to manage because attempts to connect over HTTPS often fail. This started because I was finding that the NAS had become invisible on the network so I couldn't even browse it in the File Explorer. A restart usually makes it visible again, although at the time of writing, having just done a hard…
-
NAS326 - Degraded issue. Volume 1 got degraded after switching to RAID 1
After a while I decided to add a second disk to use in RAID 1 for the volume 1, here's some specs: Disk 1 - Volume 1 - 500GB, 43GB used Disk 2 - Volume 2 - 1TB blank brand new I first installed the new 1TB drive and than changed the Volume 1 raid mode to RAID 1. The next window showed me all the correct options, disk 1…
-
Zyxel NSA325 v2 shows status degraded after HDD replacement
Hi, as one of my 2 2TB HDDs (working in RAID1 Mode) died a week ago, I replaced it with another 2TB HDD. Initially after replacement all went well, the System started the repair and after a wile the volume status switched to "Healthy". Now it shows "Degraded" again - even if now both disks are showing up as "Healthy" in…
-
Can anyone advise on internet access for an old NSA310 NAS drive?
Hi guys. Very technical user here in other areas of PC work but not network experienced in the slightest. You network managers are Gods to me! What is it they say? "In the country of the blind the one eyed man is king." ;) I'm trying to set up an older NSA310 so I can access my data on it when out and about from my home, I…
-
NSA325v1 login problem
Hello everyone, After several weeks of not logging on to the http admin console of my NSA325v1, I am now getting the following error message. I'm sure I'm entering the right password. To further rule that out, I've logged on as root via SSH and reset the password (passwd admin). Even after changing the new password and…
