-
connect Qnap storage to Zyxel XS1930-12HP 10Gbit port
Hi! Is ti possible to connect my Qnap storage with SFP+ port to Zyxel XS1930-12HP 10Gbit SFP+ port? Can I use Zyxel DAC10G-3M-ZZ0103F for this purpose? Some people report that it's for stacking only Best regards, Stephen
-
GS1920-24HP POE extend mode?
Good morning, I'm new to these switches, and have a couple questions for my issues. 1st one is I'm trying to locate the extend mode on the poe port. The GS1320 switch is easy to locate but this GS1920-HP is a different story..lol 2nd is I'm using Cat6 splitters to run IP cameras. Foe some reason its not playing nice with…
-
XGS1210-12 Link Aggregation
I bought a XGS1210-12 and wanted to connect my NAS with two eth interfaces via LAG mode 4 to the Switch. Looks like the XGS1210-12 is not supporting IEEE 802.3ad / LACP. Am i right? Can sombody tell me what LAG modes are supported under Linux?
-
My zyxel keeps going down and not reboot
Hello, My zyxel XGS1930-28 keeps going of line. Could anyone explain why?
-
Lancom Router - Zyxel GS1920 - FritzBox (as Router) - DHCP not working
Hi,I have a relative complex setup.- my LANCOM 1902VA works as Internet Interface and DHCP Server- my ZYXEL GS1920 works in this setup as Access Switch- attached to the GS1920 is a FritzBox configured as Router The connection to the FritzBox works. The FB even grabs its IP-Address via DHCP (setup in the LANCOM as BOOTP…
-
Zon Utility page (and many other in website) doesn't work
Hi, I must say, I'm not getting the best first time experience with your product and website at all. I'm trying to download the Zon Utility to setup my new MG-105 switch. The problem is, it directs me to a form to fill in. When I submit that form, 4 out of 5 times it just redirects me to the same page. The 5th time it's…
-
Zyxel MG-105/MG-108 Interoperability issue with Orange Livebox6
We have recently confirmed a chipset IOP issue on MG-105/MG-108 for the Green Ethernet Technology (EEE) with Livebox6 gateway from Orange, the French service provider. The result is random and may depends on either cable quality or lengths. There are similar discussion on the Orange forum across different brands of…
-
Zyxel Switch with Wazuh SIEM
Hi guys, I need to make wazuh able to integrate with Zyxel switches. Is there already any guide/discussion about this?
-
Manual for gs1920-24hp
Hi there, I am looking for the above manual but the Zyxel website only provides the version 2 (gs1920-24hpv2) one. Any help is highly appreciated. Thank you so much.
-
No 2.5gbs XS1930-12HP and NWA210AX
HI there have recently upgraded from a unifi setup, i am by no means the best network engineer but run an okay home system, purchased the above switch and access point and i cannot get it to link at 2.5gbs, if i set auto it negotiates at 1gbps and if i manually set 2.5 on the switch port the access point doesn't connect…
-
Issues with 2.5g realtek and XS1930-10
I got myself a Zyxel XS1930-10 switch and I am using it with a PC with MSI X570 Unify motherboard that has a RTL8125 2.5 Gbps LAN controller. XS1930-10 is then connected to my XGS1930-28HP with a 10g SFP+ patch cord. My ethernet infrustructure is all cat6 certified (running cables, patch cords, patch panel and terminals).…
-
Getting an error registering my new switch
Hi - Hope we all had a nice Christmas - I have lovely new xGS1210-12 and I would like to register it. It was purchased via amazon from Zyxel Communications. I have created a Zyxel account to register the device and it complains about the reseller - any ideas? thanks
-
XS1930 Error: Add policy rule failed!
Good afternoonWhen adding a rule to XS1930-10, an error Error occurs: Add policy rule failedPlease clarify what the problem may be
-
XGS2210-52 Change IGMP Query Interval via CLI
Hi there, we have a XGS210-52 switch. We want to alter the IGMP querier interval. For now the general queries are sent each 125 s. We checked with Wireshark. In the web UI there is no parameter available. We checked the CLI documentation. To read out the actual value the command show ip igmp timerreturns Invalid commant…
-
No Internet at connection
Just got these in the mail and plugged them in. Computer is telling me there is no internet connection and wifi is extremely slow. All lights green.
-
GS1200-8HP v2 VLAN I'm not getting it (probably stupid mistake setting PVID on wrong port)
Hi, As I said, not getting it =) Port 4 has my ISPs WAN incoming connected.In my world, that traffic should be possible to pick up on VLAN20 on the other ports, or?Firewall connected to port 8 has it's interface tagged with VLAN20 which is WAN. LAN interface untagged. VLAN30 and 50 are iot and guest VLANs. So, anything…
-
Are firmware files still available for legacy products like "ES-1552"?
The following archived link lists tons of firmware files but there aren't present anymore: https://web.archive.org/web/20190828033314/ftp://ftp.zyxel.com/
-
Missing Menu after FW Upgrade
After a FW upgrade through Nebula, I am missing Menu points on my local web administration. I tried rebooting,loading and resetting the config,but nothing helps. It feels like I lost my admin privileges. the pic shows the available options under “advanced application”
-
WHAT IS THE MAXIMUM NUMBER OF CONNECTED DEVICES/USERS IN ZYXEL USG FLEX 100?
Good day Everyone! WHAT IS THE MAXIMUM NUMBER OF CONNECTED DEVICES/USERS IN ZYXEL USG FLEX 100?
-
MG-108 upload speed are limited to <400MPS
I am testing the 5G CPE on their mmWave throughput. I need to compare the performance on different PCs. When I use MG-108 the DL speed is perfect. But UL speed only 300+ MPS. My ISP has symmetric traffic flow which support 1G DL/UL. My connection is below: 1. ISP -> MG-108 -> PC 2. ISP -> PC Test results are below: 1. DL…
