-
M1 no roaming to satellite
very simple network 1 primary cable connected and 1 wireless satellite. Setup was easy and successfull and things work correctly (no changes in options; separated wifi 5 and 2.4; firmware updated; optimal distance between devices) - setup was done first time by web configuration on cabled PC and after a reset second time…
-
WSM20 why 2 out of 3 do not use WAN port?
Hello, i just installed a kit of 3 pieces of Zyxel Multy M1 AX1800. My LAN is like that: 1 TPlink router → ethernet →1 Zyxel 8 port poe switch → ethernet → 3 Multy M1 devices. i notice a bad thing, although all 3 Multys are connected to the WAN port with the network cable, only the master uses it. The other 2 connect via…
-
How to connect second mesh unit
-
Windows 7 does not see Zyxel M1
Dear All, I have a newly installiert Zyxel M1 Mesh system with Digitaliserungbox Premium 2 (Telekom). I have also an old Windows 7 PC (Lenovo Thinpad X240) which can access all the wireless networks even if I share my mobile hotspot, but it doesnt sees the Zyxel Mesh so I am not able to join to my home wifi with this…
-
4 satellites added to a Multi M1 router - it is fine?
Dear Support Team, In the below link I could read that only 3 satellites can be added to 1 M1 router. However I could add 4 satellite. It is normal? What side effects can I have? Thanks
-
Multy M1 - 5G keeps switching between nodes
Hi, I have some problems with my 5Ghz connection on my Multy M1. For some reasons, the nearest sattelite (connected via UTP to main node), is dropping the signal (I assume an attempt to force me to another bide), so my device tries to connect to the main router, but I think the signal's to weak for a proper connection so…
-
Multy m1
Good morning, I am attaching the system diagram. I tried connecting the mesh line first, and then wiring it via the switch, but only the main router connects via cable, the satellite routers, even if connected via Ethernet cable to the WLAN port, are connected via Wi-Fi. For greater speed I should: 1: create three…
-
Setup Multy M1 in Access Point mode? How?
I am trying to connect these to my network, but the initial setup page I accessed via the website will not run without plugging the M1 into my network via the LAN port and then I have all kinds of issues. Is there an easy way to add this device as an access point? I have configured my DHCP server to allocate IP addresses…
-
Dropped wifi
My Apple phone logs onto my Multi X WiFi network but when my phone opens from sleep mode it’s not connected to the WiFi and if I go into the Multiy X app it says that it connecting. WiFi will then connect #MultyX_Nov_2018
-
Multi M1 unblock
Why is there a function called “always block” and you can’t unblock. no regrets what so ever. But is there any way to unblock anyway??
-
Instable wlan
I’ve got an issue with wlan. Sometimes I loose connection and asks one of my systems to fill in the password again. How is that possible ?
-
Multy M1 WSM20 AX1800 - satellite slow internet
Hi, I have 3x M1 mesh devices named and configured as follows: Router - This is the "Main" device connected with an ethernet cable directly to my NR5103 internet router. Squidge - a satellite router in a bedroom, connected via wireless to the Router. Backhaul reports "perfect" Lounge - another satellite connected via…
-
Multy M1 AX1800 - Mesh not working when in bridge mode
Hello, When I configure my 2 M1 in standard mode, the mesh is working as the two M1 have a green led on. However, when I put them into bridge mode the sattelite's led stays red as if it would not connect to the internet. Does someone have a solution for this Problem ? Regards
-
Wifi test
when i want to test wifi signal i get an error with message: connect the device with multy network, bit my iphone is connected! And in other forum i wrote that the wifi is very very unstable. I thoughy mesh system was to created a stable and fast wifi in your house but my wifi was better with the cheal router from my…
-
M1-latest firmware version
Hi, What is the M1's latest firmware? Is it v1.00 (ABZF.5)C0? Why my M1 is back to V1.00(ABZF.4)C0?
-
Multiples bugs on Multy M1 AP
Hello, I notice many bugs on the AP Multy M1, including: -> When disabling the WPS from the web interface, the master AP correctly applies the parameter but the satellites (WPS still active on them). -> Unable to apply 40 Mhz bandwidth on 2.4Ghz Wi-Fi (parameter applies to master but not to satellites) -> Regularly an SSID…
-
Multy M1 wired Mesh extension possible?
I found a bargain on this product, but before going to buy I wanted to know if it is possible to connect these Mesh devices also by LAN cable so that the extension signal will be better?
-
Multy M1: wifi backhaul remains active with wired setup
I have 3pack M1s, setup in wired topology. In wifi analys app I notice that hidden Networks remain active as well. I think this is unnecessary and creates unnecessary transmissions and draws unnecessary power. Why is the wifi backhaul not suspended in wired config? Can the wifi backhaul be stopped in some way?
-
Devices logged into Multy X app
Hi, a colleague and I were managing our Multy X app and devices. We both logged in the apps using the same Zyxel Cloud account. Recently, I have changed the password but she told me that she is still logged in. I did not find the list of logged in devices using a Zyxel cloud account. My questions are that: 1. Is it true…
-
Problems with connecting multy u
I downloaded The app connected multy u with Ethernet cable to wall rj42 and plugged in Power IT turns blue and when i try to create name and password IT says applying tour wifi settings to multy For like 3 mins and Then says "setting failed multy requires reset. And after i do reset IT just says connection Timed Out when i…