-
Do APs managed via Nebula also work without connection to Nebula
We are using NWA90AX and we are wondering, if they keep working properly without an active connection to Nebula.
-
Login NWA1120 Series
Hi everyone! In spite of the fact that my Zyxel PoE Access Point sounds like it would be cool (NWA y'all) - it is not. I've inherited this problem: I can't login into the config dashboard. The IP is allegedly 192.168.1.2 but nothing I can do seems to be able to get me to the login page. Has anyone encountered this issue…
-
WAP 3205v3: dissatisfactory performances while used as AP client
Tested in three different scenarios: = D-Link DSL-2740B as source. Before losing connection, no more than 48 hours. = ISP-branded router, Technicolor should be the name of the builder but not sure about the underlying product. 802.11ac as wireless standard. No more than 16 hours before loosing connection. = TP-Link RE200v5…
-
NWA50AX - just upgraded firmware and speed now really slow
Hi, I've just upgraded the firmware on my NWA50AX's tobV6.29(ABYW.3) and the performance of my WiFi has dived. Broadband speed about same as normal 50MB/s but now huge delay on download speeds. I have 5 NWA50AX devices all hard wired back to the SKY router so they are acting as access points. All were working fine until I…
-
How do I remove an AP from NCC without access to that NCC?
I purchased a WAX650S used and it's locked to an NCC account that I do not have access to. I only need local admin mode. Resetting the AP and/or copying /conf/system-default.conf to /conf/startup-config.conf do not have any effect. How can I separate this AP from NCC? Thanks.
-
NWA50AX VLAN not working
I have a NWA50AX and I want 2 VLANS I have set up on my router to pass through the WiFi. I have changed to Standalone management, have configured the 2 VLANs with tags 10 and 20 on the AP (with the wizard) but its not working. I have tagged ports 1 and 4 (which is where the acces point is connected). My VLANs work for my…
-
nwa220ax-6e ax201 5ghz wpa3 combination does not work
Hi, I have 2 nwa220ax-6e and when I turn off transition mode on the AP for WPA3 on 5ghz, ax201 card is not able to connect. It works with asus and unifi. Can you please fix this? Also when do you plan to include turning off of transition mode option into nebula pls? This option is now disabled. Thank you
-
Slow WebInterface on NWA90AX Pro
I am experiencing similar issues as in "Slow WebInterface on NWA50AX Pro" thread but on a NWA90AX Pro. Many of the flows that pass via the AP experience Freezes (at TCP level, packet capture shows, DUPs, retransmissions, etc) including accessing the WEB and SSH interfaces of the AP itself when from not-administrative…
-
low coverage
We have a NWA110AX on site, how should we configure the radiosetting to get the maximum coverage. As for actual situation our issue is that we are having a coverage of only 3 meter on open space and radio settings is on custom. Kindly help on this matter. Regards Rahul
-
NWA50AX Syslog format issue
I noticed another thread from earlier in 2023 asking about CEF format messages: Device: NWA50AX, firmware: V6.29(3) I am collecting regular syslog messages, the received messages are like this: <141>1 2023-12-28T20:22:59+00:00 2023 NWA50AX - - - NWA50AX src="0.0.0.0:0" dst="0.0.0.0:0" msg="Station: 99:99:99:99:99:99…
-
NWA50AX PRO & NWA50AX connection status issues
Hello, I have recently started to have issues where the two NWA50AX's and a single NWA50AX PRO continuously go off line and on which is meaning devices keep redirecting to another access point which is on line or drop off line completely. They have been working fine with no issues for months but recently started and…
-
Wifi
how do I renew my internet
-
Low performance on NWA50AX
Hi! I recently installed a single NWA50AX for a client. After successful deployment I went and tested the speed. While I did not expect for Wifi speeds to reach 1Gbps I was quite surprised to see that speed measurements showed speed of max 400Mbps. Configuration: -1st NWA50AX - Wifi settings: BSSID on 5GHz @80 MHz(2.4Ghz…
-
NWA90AW Which SSID is 2.4G / 5G
Hi I have just purchased a NWA90AW, however I don't know which SSID is which Need to label them as 2.4G and 5G on the broadcast How do I tell which is which from this screenshot I guessed the SSID1 would be the 2.4G and the SSID2 the 5G, but download speed appears to be the same
-
NXC2500 high CPU usage / Sessions
Hey there, i have a NXC2500 and 5 NWA5123-AC for 5 years and it works great. But since a few weeks the CPU Usage from the NXC2500 goes up to 100%. I can see that the Session count is between 2k and 10k and then the CPU usage is very high. But i cant find a solution and hope you can help me. The Firmware from the NXC2500 is…
-
NWA1123-NI has the wrong firmware and will not accept new firmware
I have uploaded firmware version V211AABJ0C0.bin (belonging to a NWA1121-NI) to my NWA1123-NI. The web interface demonstrates that it thinks it is an NWA1121-NI. It works a little, but often loses all connections. I was hoping that updating the firmware to the correct one (V211AAEO0C0.bin) will correct the issues, but I…
-
Lost access to AP's SSID setup in Nebula
I started setting up 5 new access points (NWA50AX) a couple days ago. I was able to configure them in Nebula, but now I cannot get to any SSID configuration options in Nebula. If I go to the Wifi SSID settings page, it tells me I need to add at least on SSID. If I click on the "advanced mode" slider, it gives me the…
-
NWA50AX Pro - NWA90AX Pro differences
What are the differences in features/performance between those two APs? I couldn't find information about it. Specs seem to be same.
-
LLDPD is Dead NWA210AX (Rebooting every 15 min)
After last nights weekly reboot I'mm getting this error in the logs and my APs are rebooting themselves every 15 minutes……. This is in the log just before reboot happens: 2023-11-25 23:51:59 alert System lldpd is dead at Sat Nov 25 23:51:59 2023 App Watch Dog 2 2023-11-25 23:51:59 alert System App watch dog stop to recover…
-
nwa50ax keeps showing offline . HELP
Hi I have 3 NWA50AX WAP's all powered POE switch via Lan cable . One of them has started going offline . The other 2 are fine . I also see the the one that goes offline when it comes back up it shows it is Uplink: 100M/Full. Not Uplink: 1000M/Full. like the other 2 Any ideas? This is the status of the problem one This the…
