-
Multi mesh system with multiple dropouts since changing ISP
I had a multi system (2 multi x and 2 mini multis) creating the network from my Virgin Router. Since changing to Zen internet (a BT system with a fritz box) I am struggling to keep connections. My computer and phone are ok, but slow and glitchy but the printer, solar and EV charger have not connectected since and the TV…
-
Zyxel Multy M1 - network topology for ethernet backhaul
I have bought a Zyxel Multy M1 3-pack of which I would like to connect 2 stations with ethernet backhaul and the other wireless (no ethernet connection available in that room). However, after installing the system in bridge mode, it was very unstable. Roaming didn't work well and it quite often happened that the wireless…
-
Problems with Multy M1 connections
Hello over the last few days (starting Saturday 1st June I think) my Multy m1 system has started to have repeated connection issues. I have 5 satellites and all continue to connect and disconnect on a 3-4 minute basis. I have tried a fixed IP but that didn’t help. Has the latest update introduced this problem? Does anyone…
-
Multy m1 Internet speed fluctuation
I am using it as a wireless mesh and the first device has a wired connection, but the speed drops on its own, and the same is true for other devices. Signal strengths between -65dbm and -70dbm There are no signal interrupters, but the speed still drops This normal Speed my internet 100/50 mgbit Last Device loses too much…
-
Multy M1
Hello all, my Satelite always disconnects. And randomly no internet connection. I already have tried to reset all satellites and Master, logged out of the account and reinstalled the app on the iPhone and set up all master and satellite new but with no success.
-
Multy M1 won`t connect to ISP without connecting ISP`s router first
I've had the Multy m1 x3 set for a while and have always had the same issue, let me explain. I moved over to swish fibre around 8 months ago and they installed the ONT (ADTRAN 622v) modem and i was given a plume superpod. This has terrible wifi and is even worse through the switch/powerline adaptors so i purchased the…
-
Multy M1 won`t connect to ISP without connecting ISP`s router first
I've had the Multy m1 x3 set for a while and have always had the same issue, let me explain. I moved over to swish fibre around 8 months ago and they installed the ONT (ADTRAN 622v) modem and i was given a plume superpod. This has terrible wifi and is even worse through the switch/powerline adaptors so i purchased the…
-
Server problems, firmware update?
A few days ago, a firmware update was offered to me (two WSQ60 and one WSQ20). At that time, I wasn't able to proceed right away. Now that I have some more time available, my Multy app isn't able to connect to the server; for a quick moment, my devices are showing, but then they disappear and there's an error message about…
-
Multy M1- Wifi Keeps Showing no Internet, devices disconnecting
Hi, I've got a 3 unit setup. Primary and 2 Satellite nodes. Backhaul to the Satellites nodes is via 1Gig ethernet. I am connecting to the WAN/LAN port on all devices. Primary is setup in bridge mode to an openwrt router. I'm getting regular WIFI disconnects on my devices. I have a Google Home device on my desk and it keeps…
-
Multy X goes "offline"
I have a network of 4 X Multy X (one at each corner of my house about 50 feet apart. The primary Multy is in my study. The Lounge unit regularly, but at random intervals, goes offline (a message on the Multy App states "Offline, please check the power connection). I have to switch off and then back on and wait about 10…
-
Multy M1Node keeps showing as offline
Hi, I own a twin pack of Multy M1s, and have an issue with the node/router. I’ve noticed over the last few weeks of ownership the node shows as being offline after a couple of day in both the Multy app and web interface. However, it does appear to still be online as devices connected to it have an internet connection. The…
-
Multy M1 app hidden page connected devices
Hello, I am using IOS app to configure Multy M1. due to routing limitation I have to use the bridge mode. When a new device is discovered, the multy app sends a notification (picture 1) and when clicking on it, I am able to access the page where all devices are listed (picture 2). in order to see who is connected, and get…
-
M1 5GHz switches to 20MHz bandwidth randomly
Zyxel M1 randomly switches from 80MHz to 20MHz band for the 5GHz network. This is temporarily solved by rebooting but happens again after some hours, or a couple days maximum. I have 3 M1s connected via Ethernet backhaul, one base station and two satellites, one for each floor. The issue happens consistently, and…
-
M1 Multy - Problem found, 5G wifi is not working so thats why no mesh. Question, how to solve it?
Why is the 5G network not working??? Channel auto or fix?
-
M1 Multy after restart no wifi, mesh is not working at all.faulty manufacturing? wast of money?!
Dear, Iam trying to configure a simple mesh system at home. BUT backhaul perfect internet zero. Why??? The M1 Multy works only on cabel, it is a cabel mesh system. Even its working, but today after restart no wifi, i cant connect, is not finding the password. etc. The product has 100 bugs, is not usable. Lot of people has…
-
Multy M1 - Satelits how far from Main Router? How many dBm works fine?
-
WiFi connection getting disconnected while roaming (Multy M1)
Dear Zyxel, I have setup an M1 system with 1 master Mesh and 4 slaves. There is one Mesh slave where I go, the internet disconnects. Actually maybe it happens in some more areas, but in living room it happens most of the time. I have setup 5G and 2.4G networks. I tried to use only 1 SSID before (one name and one pw) but it…
-
Why is my multy m1 generating constant ptr queries
Looks like my multy m1 is generating constant stream of reverse dns lookups of the network, example below. 192.168.10.164 is my main and 192.168.10.58 is a satellite, and the system is set to bridge mode. Any reason why, and how to limit it? time type domain client status reply 2024-04-22 13:47:31 PTR…
-
WSR30-Q50-Q20 Scheduled SSID
Hi Team, Just a quick question to know if the WSR30,Q50 and Q20 have the Scheduled SSID fonction? Thanks a lot in advance,
-
Multy M1 client not listed
dear community, I’m using a Multy M1 as wireless access point and one cabled client. the cabled client is not visible in the client’s list (parental control). How is that possible? And how to make it visible? thanks
