-
Bridge mode and satellites
I have a Multy M1 connected to my primary router using the M1 Wan?lan port in bridge mode so the primary router handles DHCP etc . The M1 has a static ip from the primary router. I have not been able to establish a satellite with this set up. Should this be possible and would the satellites get IP addresses from the…
-
Multi M1 with TV Orange
All run fine , master & satellit But i cannot use my TV BOX Orange ( no flux tv ) I have before yhis porblem with Asrock G10 & OpenWrt as this post IGMPPROXY ??? Solution for me: build a OpenWrt firmware & flash but i cannot because i have not console login/password Can you help me ?
-
I would like to use static ip addresses on WSQ60 Multy PLUS
I tried to use the reserve IP in the access list that generate a rule in setting lanand i put some rule to in setting lan to force the devices to get a specific ip address it works for a while but after a period non well understood the wsq60 cancel the rules and in the access list took off all the reserve ipso i am back at…
-
IPTV function for Multy m1
dose multym1 support iptv function in Taiwan?
-
How can I restrict access to adult content on the multi x router?
the web app only allows for restrictions of access times via profiles, as far as parent controls this is inadequate
-
Multy M1: specify VLAN with PPPoE
Hi, I need to use the Multy M1 as router. My ISP provides an ONT in my home: I just need to attach the WAN port of the Multy to it, and configure the username/password and VLAN id, which my ISP (Vodafone) provides. It's a simple configuration I successfully applied with other routers and mesh systems. However, Multy PPoE…
-
Multy M1
What is the max throughput of a Multy M1 on PPPOE? In a test it is maxing at ~330Mbps? I am connected to a 1Gbps FTTP. The cable between the FTTP and the Multy is high quality CAT7 and only 1M in length. Is this just a test rather than a speed test?
-
Multy M1:Can not add a satellite after setting up "brigde mode" in the main router
HelloI am having several problems setting up a satellite with my MULTI M1.I have the main M1 router connected directly to the ISP router. Initially, I configured both router and satellite through the WEB GUI (since neither WPS worked, nor the app has worked on 5 different devices). Up to that point, apparently everything…
-
WSM20 too close
Good morning everyone, I have recently buy a kit of WSM20 spots with 3 devices in the box. I have installed the first 2 spot, checked the backhaul and seems al working well. After some hour I have checked the backhaul again because seems that my phone doesn't automatically switch between WSM20 spots: the result is that I…
-
Where is the device list ?
Hello, I have just installed fews M1ax1800, Bridged mode. I can’t find any option to view a list of devices connected or offline etc. The only way to access to a sort of list is when a new device is just descovered, then a notify pop up on my IPhone 14 pro max iOS 16.3 and I have to click on the notify. How can I solve it…
-
Dynamic DDNS provider// Zyxel Multy M1 WiFi 6 AX1800
hello I want to buy Zyxel Multy M1 WiFi 6 AX1800 . my question is if this allow https://www.noip.com/ ddns provider ? thxs!
-
Multy M1 wifi device count support when using multiple satelites
Hello, 1) I read that the number of wifi devices supported is 128, is this number increased when using multiple M1 in an ethernet Backhaul setting? _______________________________________________________________________________________________ 2) is the 254 device (wired+wireless) due to ip routing coinsiderations or MAC…
-
Does Multy M1 support WOL?
I have Synology NAS and enable the WOL. also set the port forward in M1 Does M1 support “Magic Packet”?
-
Future Application Support
Hello,I think that multy wifi systems should be accessible via web interface because of the risk of future application support being cut.If the support is cut, there may be serious problems with the installation of devices.
-
Change or switch the Multy Router (X) to a different node
I have 3 Multy X, WSQ50 (A, B, C) I want to change which node the Multy Router (Primary) is on e.g. From A -> C Can I simply delete it and another will be promoted to Router? I need to unplug the existing Multy Router (Primary) for an extended period and cannot physically reach or swap the location.
-
Multy X app can no longer display connected devices after latest update
My Multy X system was working fine until the most recent update. Multi: V2.20(ABKJ.8)C0 App: 2.5.4.221229 The parental control icon is greyed out. How can I get the connected devices to display again? Many thanks
-
Multy X - eternal white LED flashing
I have 4 Multy X, one of the satelittes was showing offline and I power cycled it. Now it is flashing white, and has for 3 days. - Tried reset for many many seconds -> no response - Tried power cycle many times with and without LAN connection -> no change. How can I factory reset or force new firmware. Any ssh options or…
-
Multi X WSQ50
I have a three node multi. One is connected to the PPPoE, another is on an ethernet backhaul. The third is on the WiFi backhaul. I am having an issue with the third, after several factory resets, restarts and a full reset of the mesh it refuses to offer up internet either via ethernet or WiFi. The setup of the node goes…
-
How to set up a static IP address for a client device via Web GUI?
Step 1: Access the Web GUI with a web browser. * Open a browser such as Chrome, Firefox, Safari and so on. * Type http://zyxelwifi.com, http://zyxelwifi.net or http://192.168.212.1 (default IP address) in the address bar of the browser. In order to be able to access the Web GUI, you might have to get the correct IP address…
-
Can't setup my Mesh, iPhone Multy app
Hi guys! I'm having problem setting up my wsr30 using Multy APP on iPhone (iOS 16.1.1).If i'm logged in on app, it does not finish the setup, just hangs on "connecting network" -state. If i'm not logged in, setting up the Multy without cloud, it does finish, but I just can't change anything. Settings and everything else is…
